flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the user with a boolean control then automatically select
the deemphasis filter most closely matching the sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're already flagged as using symmetric rates so we don't need to
have a custom implementation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: Mario Becroft <mb@gem.win.co.nz>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32,
rather than WM8580_AIF_LENGTH_24.
Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit.
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.
Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
We want the index of DAI's driver here.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In alc5623_i2c_probe(),
the default case for checking alc5623->id behaves the same as case 0x23.
However, In alc5623_probe() the default case for checking alc5623->id
becomes to be the same as case 0x21.
This makes the meaning of default case inconsistent.
Since we have checked codec id in alc5623_i2c_probe() by comparing
vid2 with id->driver_data, it is not possible to run into the default case now.
In case we may add more supported devices to alc5623_i2c_table in the future,
this patch changes the default case return -EINVAL to let people know that
they should not run into this case. They should also add a new case accordingly
for the new id.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update some of the default configuration for the device to improve
the performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The deemphasis filter should be selected based on sample rate for
optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is much more maintainable than the array.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The mute/unmute is controled by SMUTE (Soft Mute Control bit):
0: Normal Operation (Default)
1: DAC outputs soft-muted
I think this change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
According to the datasheet the bypass path enable/disable is
bit 3 therefore we need 0x8 and not 0x4.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
During playback start the codec has been already powered at
BIAS_ON event time, so there's no need to enable the codec again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need to enable the codec at this time.
The codec will be enabled later by other events
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Simplify pm860x_probe error handling and return actual error code we got.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to communicate our power management state back to the
parent device, allowing it to do a full power down when the device is
idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 and WM8958 register map is relatively sparse so benefits
from compression. The rbtree compression gives better results than
LZO for both memory and CPU consumption on a map as sparse as this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the process we convert the driver to read registers one at a time
when initialising the cache. This has the effect of working around
limitations in the sizes of I2C transactions which can be done by some
CPUs. Due to the sparseness of the register map the overhead from this
should be minimual unless I2C transactions are very expensive to start.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 contains an advanced accessory detection feature which allows
detection of up to seven different impedence levels on the microphone
bias output, including detection of video outputs. Since some of the
more involved accessory interfaces may involve noticable interactions
with external components a simple detection scheme is provided by
default with the option to provide custom handling of accessory detect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 features a multi-band compressor which can be enabled on
any of the AIF inputs. The MBC allows different gains to be applied to
differnt audio bands, providing an improvement in perceived loudness
of the signal by avoiding overdriving the output transducers. This
patch enables support for the MBC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Additional audio routing options are available on the WM8958 audio
interface 3. Add support for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 is a WM8994 derivative. This patch merely ensures that some
revision specific configuration for WM8994 is not enabled on WM8994,
additional patches will add support for the new features introduced on
the WM8958.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
