Since !LI_CCFG_* evaluates to 0, this did not change anything to
cfgval and ctlval.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2.6.31-rc7 does not boot on vSMP systems:
[ 8.501108] CPU31: Thermal monitoring enabled (TM1)
[ 8.501127] CPU 31 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
[ 8.650254] CPU31: Intel(R) Xeon(R) CPU E5540 @ 2.53GHz stepping 04
[ 8.710324] Brought up 32 CPUs
[ 8.713916] Total of 32 processors activated (162314.96 BogoMIPS).
[ 8.721489] ERROR: parent span is not a superset of domain->span
[ 8.727686] ERROR: domain->groups does not contain CPU0
[ 8.733091] ERROR: groups don't span domain->span
[ 8.737975] ERROR: domain->cpu_power not set
[ 8.742416]
Ravikiran Thirumalai bisected it to:
| commit 2759c3287de27266e06f1f4e82cbd2d65f6a044c
| x86: don't call read_apic_id if !cpu_has_apic
The problem is that on vSMP systems the CPUID derived
initial-APICIDs are overlapping - so we need to fall
back on hard_smp_processor_id() which reads the local
APIC.
Both come from the hardware (influenced by firmware
though) so it's a tough call which one to trust.
Doing the quirk expresses the vSMP property properly
and also does not affect other systems, so we go for
this solution instead of a revert.
Reported-and-Tested-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shai Fultheim <shai@scalex86.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A944D3C.5030100@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Initialize cx before calling xen_cpuid(), in order to suppress the
"may be used uninitialized in this function" warning.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Xen always runs on CPUs which properly support WP enforcement in
privileged mode, so there's no need to test for it.
This also works around a crash reported by Arnd Hannemann, though I
think its just a band-aid for that case.
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for sa1100_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for au1k_ir.
Untested.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When page alloc debugging is not enabled, we essentially accept any
virtual address for linear kernel TLB misses. But with kgdb, kernel
address probing, and other facilities we can try to access arbitrary
crap.
So, make sure the address we miss on will translate to physical memory
that actually exists.
In order to make this work we have to embed the valid address bitmap
into the kernel image. And in order to make that less expensive we
make an adjustment, in that the max physical memory address is
decreased to "1 << 41", even on the chips that support a 42-bit
physical address space. We can do this because bit 41 indicates
"I/O space" and thus covers non-memory ranges.
The result of this is that:
1) kpte_linear_bitmap shrinks from 2K to 1K in size
2) we need 64K more for the valid address bitmap
We can't let the valid address bitmap be dynamically allocated
once we start using it to validate TLB misses, otherwise we have
crazy issues to deal with wrt. recursive TLB misses and such.
If we're in a TLB miss it could be the deepest trap level that's legal
inside of the cpu. So if we TLB miss referencing the bitmap, the cpu
will be out of trap levels and enter RED state.
To guard against out-of-range accesses to the bitmap, we have to check
to make sure no bits in the physical address above bit 40 are set. We
could export and use last_valid_pfn for this check, but that's just an
unnecessary extra memory reference.
On the plus side of all this, since we load all of these translations
into the special 4MB mapping TSB, and we check the TSB first for TLB
misses, there should be absolutely no real cost for these new checks
in the TLB miss path.
Reported-by: heyongli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the write to PMBR1 register through I2C. Also, the constant which
holds the value to write is now called TWL4030_GPIO6_PWM0_MUTE. This
name is based on TRM to avoid confusion.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: Prevent dead lock on clockevents_lock
timers: Drop write permission on /proc/timer_list
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix too large stack usage in do_one_initcall()
tracing: handle broken names in ftrace filter
ftrace: Unify effect of writing to trace_options and option/*
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix build with older binutils and consolidate linker script
x86: Fix an incorrect argument of reserve_bootmem()
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
xen: rearrange things to fix stackprotector
x86: make sure load_percpu_segment has no stackprotector
i386: Fix section mismatches for init code with !HOTPLUG_CPU
x86, pat: Allow ISA memory range uncacheable mapping requests
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Improve error message that changing journaling mode on remount is not possible
ext3: Update Kconfig description of EXT3_DEFAULTS_TO_ORDERED
1) Added support of internal subwoofer (it sounds!!!)
2) Auto muting front speakers and internal subwoofer on headphones plug.
3) Internal mic works.
4) 3 channel mods (jack maps):
black pink blue
2ch: front ext mic line in
4ch: front ext mic surround
6ch: front CLFE surround
Can be changed in mixer.
5) Sound can be recorded from:
Internal mic
Ext mic
Cd
Line in
6) 2 separate capture channels.
Signed-off-by: Denis Kuplyakov <dener.kup@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When I rewrote tty ldisc code to use proper reference counts (commits
65b770468e98 and cbe9352fa08f) in order to avoid a race with hangup, the
test-program that Eric Biederman used to trigger the original problem
seems to have exposed another long-standing bug: the hangup code did the
'tty_ldisc_halt()' to stop any buffer flushing activity, but unlike the
other call sites it never actually flushed any pending work.
As a result, if you get just the right timing, the pending work may be
just about to execute (ie the timer has already triggered and thus
cancel_delayed_work() was a no-op), when we then re-initialize the ldisc
from under it.
That, in turn, results in various random problems, usually seen as a
NULL pointer dereference in run_timer_softirq() or a BUG() in
worker_thread (but it can be almost anything).
Fix it by adding the required 'flush_scheduled_work()' after doing the
tty_ldisc_halt() (this also requires us to move the ldisc halt to before
taking the ldisc mutex in order to avoid a deadlock with the workqueue
executing do_tty_hangup, which requires the mutex).
The locking should be cleaned up one day (the requirement to do this
outside the ldisc_mutex is very annoying, and weakens the lock), but
that's a larger and separate undertaking.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Xiaotian Feng <xtfeng@gmail.com>
Tested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One more patch to give a better name for the primary output controls,
this time for ALC861-VD codec. The change is simple, just checking the
pin connection whether it's a speaker-out. When both speaker and HP
are assigned, we name the volume as "PCM" as this influences on both
outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.
However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins. The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c. Thus, there
are two possible volumes.
When only one of them is used, we can name it as "Master". OTOH, when
both are used at the same time, they have to be named uniquely.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of fixed "Front" mixer name, try to assign a better name, e.g.
"Master" or "Speaker" fot the primary output volume controls of ALC260
codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When there is only one DAC is used for ALC880, try to assign a better
name, either Speaker or Front, depending on the output pin type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.
However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.
Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.
-v2: fix !SMP builds.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
s3c24xx dma has the auto reload feature, when the the trnasfer is done,
CURR_TC(DSTAT[19:0], current value of transfer count) reaches 0, and DMA
ACK becomes 1, and then, TC(DCON[19:0]) will be loaded into CURR_TC. So
the transmission is repeated.
IRQ is issued while auto reload occurs. We change the DISRC and
DCON[19:0] in the ISR, but at this time, the auto reload has been
performed already. The first block is being re-transmitted by the DMA.
So we need rewrite the DISRC and DCON[19:0] for the next block
immediatly after the this block has been started to be transported.
The function s3c2410_dma_started() is for this perpose, which is called
in the form of "s3c2410_dma_ctrl(prtd->params->channel,
S3C2410_DMAOP_STARTED);" in s3c24xx_pcm_trigger().
But it is not correct. DMA transmission won't start until DMA REQ signal
arrived, it is the time s3c24xx_snd_txctrl(1) or s3c24xx_snd_rxctrl(1)
is called in s3c24xx_i2s_trigger().
In the current framework, s3c24xx_pcm_trigger() is always called before
s3c24xx_pcm_trigger(). So the s3c2410_dma_started() should be called in
s3c24xx_pcm_trigger() after s3c24xx_snd_txctrl(1) or
s3c24xx_snd_rxctrl(1) is called in this function.
However, s3c2410_dma_started() is dma related, to call this function we
should provide the channel number, which is given by
substream->runtime->private_data->params->channel. The private_data
points to a struct s3c24xx_runtime_data object, which is define in
s3c24xx_pcm.c, so s3c2410_dma_started() can't be called in s3c24xx_i2s.c
Fix this by moving the call to signal the DMA started to the DAI
drivers.
Signed-off-by: Shine Liu <liuxian@redflag-linux.com>
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a standard parser for input pins to create the input mixer
and input source controls instead of having a difference one for each
Realtek codec. The new helper parses the codec connections dynamically
isntead of fixed indicies.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Functionality of functions omap_mcbsp_xmit_enable and omap_mcbsp_recv_enable
can be merged into omap_mcbsp_start and omap_mcbsp_stop since API of
those omap_mcbsp_start and omap_mcbsp_stop was changed recently allowing
to start and stop individually the transmitter and receiver.
This cleans up the code in arch/arm/plat-omap/mcbsp.c and in
sound/soc/omap/omap-mcbsp.c which was the only user for those removed
functions.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ca6e2ce08679c094878d7f39a0349a7db1d13675 is setting up few XCCR and
RCCR bits for I2S and DPS_A formats. Part of the bits are already set
for all formats and I believe that XDISABLE and RDISABLE bits are
format independent.
As XCCR and RCCR are found only from OMAP2430 and OMAP34xx, I move setup
of XDISABLE and RDISABLE to where those cpu's are tested and remove format
dependent part for simplicity.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use more descriptive than numerical value when showing and storing the
McBSP DMA operating mode. Show function is using similar syntax than e.g.
the led triggers so that all possible values for store function are
printed but with current value surrounded with square brackets.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_interval_list() expected a sorted list but did not document this, so
there are drivers that give it an unsorted list. To fix this, change
the algorithm to work with any list.
This fixes the "Slave PCM not usable" error with USB devices that have
multiple alternate settings with sample rates in decreasing order, such
as the Philips Askey VC010 WebCam.
http://bugzilla.kernel.org/show_bug.cgi?id=14028
Reported-and-tested-by: Andrzej <adkadk@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported by Stephen Rothwell, luckily it's harmless:
net/sched/sch_api.c: In function 'qdisc_watchdog':
net/sched/sch_api.c:460: warning: initialization from incompatible pointer type
net/sched/sch_cbq.c: In function 'cbq_undelay':
net/sched/sch_cbq.c:595: warning: initialization from incompatible pointer type
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Bspec each encoder has different sharing pipe property,
i.e. Integrated or SDVO TV both will occupy one pipe exclusively,
and sdvo-non-tv and crt are allowed to share one. The patch moves
sharing judgment into differnet output functions, and sets the right
clone bit.
This fixes both HDMI outputs choosing the same pipe.
https://bugs.freedesktop.org/show_bug.cgi?id=22247
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
After the following commit is shipped, the SDVO C detection will depend on
the SDVO_C/DP detion bit.
commit 13520b051e8888dd3af9bda639d83e7df76613d1
Author: Kristian Høgsberg <krh@redhat.com>
Date: Fri Mar 13 15:42:14 2009 -0400
drm/i915: Read the right SDVO register when detecting SVDO/HDMI.
According to the spec we should continue to detect the SDVO_B/C based on
the SDVO_B detection bit. The new detection bit on G4X platform is for
the HDMI_C detection rather than SDVO_C detection.
https://bugs.freedesktop.org/show_bug.cgi?id=20639
Signed-off-by: Ma Ling <ling.ma@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 0c2e39525b3b53a97a0202c5f35058147e53977e is not sufficient to
get fd.o bug #20115 fixed.
In addition intel_find_best_PLL() must not only rely on BIOS settings
for i9xx chips but also for i8xx, so drop the IS_I9XX() check.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
http://bugs.freedesktop.org/show_bug.cgi?id=21417
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 76db6d9500caeaa774a3e32a997eba30bbdc176b (nfs41: add session setup
to the state manager) introduces an infinite loop possibility in the NFSv4
state manager. By first checking nfs4_has_session() before clearing the
NFS4CLNT_SESSION_SETUP flag, it allows for a situation where someone sets
that flag, but it never gets cleared, and so the state manager loops.
In fact commit c3fad1b1aaf850bf692642642ace7cd0d64af0a3 (nfs41: add session
reset to state manager) causes this to happen every time we get a network
partition error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement DMA channel self linking on OMAP1510 using AUTO_INIT and REPEAT
flags of the DMA CCR register.
Created against linux-2.6.31-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2/dlm: Wait on lockres instead of erroring cancel requests
ocfs2: Add missing lock name
ocfs2: Don't oops in ocfs2_kill_sb on a failed mount
ocfs2: release the buffer head in ocfs2_do_truncate.
ocfs2: Handle quota file corruption more gracefully
* 'fixes' of git://git.marvell.com/orion:
[ARM] Orion NAND: Make asm volatile avoid GCC pushing ldrd out of the loop
[ARM] Kirkwood: enable eSATA on QNAP TS-219P
[ARM] Kirkwood: __init requires linux/init.h
2.6.30's commit 8a0bdec194c21c8fdef840989d0d7b742bb5d4bc removed
user_shm_lock() calls in hugetlb_file_setup() but left the
user_shm_unlock call in shm_destroy().
In detail:
Assume that can_do_hugetlb_shm() returns true and hence user_shm_lock()
is not called in hugetlb_file_setup(). However, user_shm_unlock() is
called in any case in shm_destroy() and in the following
atomic_dec_and_lock(&up->__count) in free_uid() is executed and if
up->__count gets zero, also cleanup_user_struct() is scheduled.
Note that sched_destroy_user() is empty if CONFIG_USER_SCHED is not set.
However, the ref counter up->__count gets unexpectedly non-positive and
the corresponding structs are freed even though there are live
references to them, resulting in a kernel oops after a lots of
shmget(SHM_HUGETLB)/shmctl(IPC_RMID) cycles and CONFIG_USER_SCHED set.
Hugh changed Stefan's suggested patch: can_do_hugetlb_shm() at the
time of shm_destroy() may give a different answer from at the time
of hugetlb_file_setup(). And fixed newseg()'s no_id error path,
which has missed user_shm_unlock() ever since it came in 2.6.9.
Reported-by: Stefan Huber <shuber2@gmail.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Stefan Huber <shuber2@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
