There's a potential race before THRE/TEMT deasserts when DMA Tx is
starting up (or the next batch of continuous Tx is being submitted).
This can lead to misdetecting Tx empty condition.
It is entirely normal for THRE/TEMT to be set for some time after the
DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely
not empty at that point, it seems incorrect for serial8250_tx_empty()
claim Tx is empty.
Fix the race by also checking in serial8250_tx_empty() whether there's
DMA Tx active.
Note: This fix only addresses in-kernel race mainly to make using
TCSADRAIN/FLUSH robust. Userspace can still cause other races but they
seem userspace concurrency control problems.
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 146a37e05d620cef4ad430e5d1c9c077fe6fa76f)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If userspace races tcsetattr() with a write, the drained condition
might not be guaranteed by the kernel. There is a race window after
checking Tx is empty before tty_set_termios() takes termios_rwsem for
write. During that race window, more characters can be queued by a
racing writer.
Any ongoing transmission might produce garbage during HW's
->set_termios() call. The intent of TCSADRAIN/FLUSH seems to be
preventing such a character corruption. If those flags are set, take
tty's write lock to stop any writer before performing the lower layer
Tx empty check and wait for the pending characters to be sent (if any).
The initial wait for all-writers-done must be placed outside of tty's
write lock to avoid deadlock which makes it impossible to use
tty_wait_until_sent(). The write lock is retried if a racing write is
detected.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 094fb49a2d0d6827c86d2e0840873e6db0c491d2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ba9e3a13c6adfa99e32b2576d20820ab10ad48a ]
An 8250 UART configured as a wake-up source would not have reported
itself through sysfs as being the source of wake-up, correct that.
Fixes: b3b708fa2780 ("wake up from a serial port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f73fd750552524b06b5d77ebfdd106ccc8fcac61 ]
Based on the fls function definition provided below, we should not
subtract 1 to obtain the correct buffer length:
fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f92ed0cd9328aed918ebb0ebb64d259eccbcc6e7 upstream.
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6214894f49a967c749ee6c07cb00f9cede748df4 ]
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b96230 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 32e293be736b853f168cd065d9cbc1b0c69f545d upstream.
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee96895 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
[biju: manually fixed the conflicts]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c4c81db5cf8bc53d6160c3abf26d382c841aa434 ]
LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.
Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.
Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 57e9af7831dcf211c5c689c2a6f209f4abdf0bce upstream.
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51f7 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31352811e13dc2313f101b890fd4b1ce760b5fe7 upstream.
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51f7 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bfdd3c654bd879bff50c2e85e42f85ae698b42f upstream.
Commit ba47f97a18f2 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8914b52e5b024e4af3d810a935fe0805eee8a36 upstream.
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0dccad87cf68fc6012aec7567e354353097ec1a ]
The currently lockless access to the xen console list in
vtermno_to_xencons() is incorrect, as additions and removals from the
list can happen anytime, and as such the traversal of the list to get
the private console data for a given termno needs to happen with the
lock held. Note users that modify the list already do so with the
lock taken.
Adjust current lock takers to use the _irq{save,restore} helpers,
since the context in which vtermno_to_xencons() is called can have
interrupts disabled. Use the _irq{save,restore} set of helpers to
switch the current callers to disable interrupts in the locked region.
I haven't checked if existing users could instead use the _irq
variant, as I think it's safer to use _irq{save,restore} upfront.
While there switch from using list_for_each_entry_safe to
list_for_each_entry: the current entry cursor won't be removed as
part of the code in the loop body, so using the _safe variant is
pointless.
Fixes: 02e19f9c7cac ('hvc_xen: implement multiconsole support')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20221130163611.14686-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a6ec673fb627c26e2267ca0a03849f91dbd9b40 ]
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
Fixes: c4d37215a824 ("[SERIAL] sunsab: Convert to of_driver framework.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221123061212.52593-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8be3a7bf773700534a6e8f87f6ed2ed111254be5 ]
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Fixes: 3c6a483275f4 ("Serial: EG20T: add PCH_UART driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221122114559.27692-1-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94cdb9f33698478b0e7062586633c42c6158a786 ]
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html
Fixes: 0dd1e247fd39 (drivers: PL011: add support for the ARM SBSA generic UART)
Signed-off-by: Jiamei Xie <jiamei.xie@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221117103237.86856-1-jiamei.xie@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ]
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1980860e0c8299316cddaf0992dd9e1258ec9d88 upstream.
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Fixes: 75df022b5f89 ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bfcbe5805d0cfc83c3544dcd01e0a282c1f6790 upstream.
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a931237cbea256aff13bb403da13a97b2d1605d9 upstream.
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 75df022b5f89 ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Co-developed-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b7dfe4833c70a11cdfa51b38705103bd31eddaa ]
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
gsm_dlci_t1()
gsm_dlci_open()
gsm_modem_update()
gsm_modem_upd_via_msc()
gsm_control_send()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221002040709.27849-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b68629bd2fb61e0171a62f2e8da3db322f5cf6 ]
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221028110044.54719-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e828e56684d61b17317e0cfdef83791fa61cb76b ]
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013112339.2540767-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8a18e3f00f3ee8d07c17ab1ea3ad4df4a3b6fe0 upstream.
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 379a33786d489ab81885ff0b3935cfeb36137fea ]
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Since commit 027b57170bf8 ("serial: core: Fix initializing and restoring
termios speed") termios speed is available also in struct console.
So properly restore also c_ispeed and c_ospeed members after suspend to fix
restoring termios speed which is not represented by Bnnn constant.
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220924104324.4035-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a6c3b3d4654fba19881cc77da61eac29f57cae ]
Currently the ignore_status is not considered in the isr.
Add a check to add the ignore_status.
Fixes: 61ec9016988f ("tty/serial: add support for Xilinx PS UART")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20220729114748.18332-5-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 566f9c9f89337792070b5a6062dff448b3e7977f upstream.
When changing the console font with ioctl(KDFONTOP) the new font size
can be bigger than the previous font. A previous selection may thus now
be outside of the new screen size and thus trigger out-of-bounds
accesses to graphics memory if the selection is removed in
vc_do_resize().
Prevent such out-of-memory accesses by dropping the selection before the
various con_font_set() console handlers are called.
Reported-by: syzbot+14b0e8f3fd1612e35350@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Tested-by: Khalid Masum <khalid.masum.92@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/r/YuV9apZGNmGfjcor@p100
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 846651eca073e2e02e37490a4a52752415d84781 upstream.
The setting of RS485 RTS polarity is inverse in the current driver.
When the property of 'rs485-rts-active-low' is enabled in the dts node,
the RTS signal should be LOW during sending. Otherwise, if there is no
such a property, the RTS should be HIGH during sending.
Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220805144529.604856-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d24d7bb2cd947676f9b71fb944d045e09b8b282f ]
In soc_info(), of_find_node_by_type() will return a node pointer
with refcount incremented. We should use of_node_put() when it is
not used anymore.
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618060850.4058525-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18a948c7d90995d127785e308fa7b701df4c499f ]
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f30e10caa80aa1f35508bc17fc302dbbde9a833c ]
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32dd59f96924f45e33bc79854f7a00679c0fa28e ]
The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fae831b3a71fc5a44cc5c7d0b8c1267ee7659f5 ]
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bec0224816d19abe4fe503586d16d51890540615 ]
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Fixes: c01af4fec2c8 ("n_gsm : Flow control handling in Mux driver")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a501ab75e7624d133a5a3c7ec010687c8b961d23 upstream.
There is a race in pty_write(). pty_write() can be called in parallel
with e.g. ioctl(TIOCSTI) or ioctl(TCXONC) which also inserts chars to
the buffer. Provided, tty_flip_buffer_push() in pty_write() is called
outside the lock, it can commit inconsistent tail. This can lead to out
of bounds writes and other issues. See the Link below.
To fix this, we have to introduce a new helper called
tty_insert_flip_string_and_push_buffer(). It does both
tty_insert_flip_string() and tty_flip_buffer_commit() under the port
lock. It also calls queue_work(), but outside the lock. See
71a174b39f10 (pty: do tty_flip_buffer_push without port->lock in
pty_write) for the reasons.
Keep the helper internal-only (in drivers' tty.h). It is not intended to
be used widely.
Link: https://seclists.org/oss-sec/2022/q2/155
Fixes: 71a174b39f10 (pty: do tty_flip_buffer_push without port->lock in pty_write)
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 716b10580283fda66f2b88140e3964f8a7f9da89 upstream.
We will need this new helper in the next patch.
Cc: Hillf Danton <hdanton@sina.com>
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5db96ef23bda6c2a61a51693c85b78b52d03f654 upstream.
Since commit a9c3f68f3cd8d (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). All
users were converted in the previous patches, so remove
tty_schedule_flip() completely while inlining its body into
tty_flip_buffer_push().
One less exported function.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f6a85158ccacc3f09744b3aafe8b11ab3b6c6f6 upstream.
Since commit a9c3f68f3cd8d (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
drivers/tty/.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e690d54cfa802f939cefbd2fa2c91bd0b8bd1b6 upstream.
If port->mapbase = NULL in serial8250_request_std_resource() , it need
return a error code instead of 0. If uart_set_info() fail to request new
regions by serial8250_request_std_resource() but the return value of
serial8250_request_std_resource() is 0, The system incorrectly considers
that the resource application is successful and does not attempt to
restore the old setting. A null pointer reference is triggered when the
port resource is later invoked.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220628083515.64138-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e35e4bf1e8dc2c8cbd5e0955dc1bd58558dae0 upstream.
The src_maxburst and dst_maxburst have been changed to 1 but the settings
of the UCON register aren't changed yet. They should be changed as well
according to the dmaengine slave config.
Fixes: aa2f80e752c7 ("serial: samsung: fix maxburst parameter for DMA transactions")
Cc: stable <stable@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627065113.139520-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff2047fb755d4415ec3c70ac799889371151796d upstream.
Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET
As was demonstrated by commit 90bfdeef83f1 (tty: make FONTX ioctl use
the tty pointer they were actually passed), these ioctls are not used
from userspace, as:
1) they used to be broken (set up font on current console, not the open
one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead
Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set
on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes
PIO_FONTRESET just return an error.
We are removing KD_FONT_FLAG_OLD here as it was used only by these
removed ioctls. kd.h header exists both in kernel and uapi headers, so
we can remove the kernel one completely. Everyone includeing kd.h will
now automatically get the uapi one.
There are now unused definitions of the ioctl numbers and "struct
consolefontdesc" in kd.h, but as it is a uapi header, I am not touching
these.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-8-jslaby@suse.cz
Cc: guodaxing <guodaxing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be03b0651ffd8bab69dfd574c6818b446c0753ce upstream.
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102add ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
Cc: stable <stable@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@penugtronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/f4d774be-1437-a550-8334-19d8722ab98c@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aabdbb1b7a5819e18c403334a31fb0cc2c06ad41 ]
__msm_console_write() assumes that interrupts are disabled, but
with threaded console printers it is possible that the write()
callback of the console is called with interrupts enabled.
Explicitly disable interrupts using local_irq_save() to preserve
the assumed context.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220506213324.470461-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b2caef400c1738b6d22f636c628d9f85cd4c4c ]
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 689ca31c542687709ba21ec2195c1fbce34fd029 ]
When the driver fails at alloc_hdlcdev(), and then we remove the driver
module, we will get the following splat:
[ 25.065966] general protection fault, probably for non-canonical address 0xdffffc0000000182: 0000 [#1] PREEMPT SMP KASAN PTI
[ 25.066914] KASAN: null-ptr-deref in range [0x0000000000000c10-0x0000000000000c17]
[ 25.069262] RIP: 0010:detach_hdlc_protocol+0x2a/0x3e0
[ 25.077709] Call Trace:
[ 25.077924] <TASK>
[ 25.078108] unregister_hdlc_device+0x16/0x30
[ 25.078481] slgt_cleanup+0x157/0x9f0 [synclink_gt]
Fix this by checking whether the 'info->netdev' is a null pointer first.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220410114814.3920474-1-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
