mirror of
https://github.com/rd-stuffs/msm-4.14.git
synced 2025-02-20 11:45:48 +08:00
5239 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Alexander Sverdlin
|
cb099fdd0c |
serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Jann Horn
|
8deb3d9018 |
tty: Fix ->session locking
commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream. Currently, locking of ->session is very inconsistent; most places protect it using the legacy tty mutex, but disassociate_ctty(), __do_SAK(), tiocspgrp() and tiocgsid() don't. Two of the writers hold the ctrl_lock (because they already need it for ->pgrp), but __proc_set_tty() doesn't do that yet. On a PREEMPT=y system, an unprivileged user can theoretically abuse this broken locking to read 4 bytes of freed memory via TIOCGSID if tiocgsid() is preempted long enough at the right point. (Other things might also go wrong, especially if root-only ioctls are involved; I'm not sure about that.) Change the locking on ->session such that: - tty_lock() is held by all writers: By making disassociate_ctty() hold it. This should be fine because the same lock can already be taken through the call to tty_vhangup_session(). The tricky part is that we need to shorten the area covered by siglock to be able to take tty_lock() without ugly retry logic; as far as I can tell, this should be fine, since nothing in the signal_struct is touched in the `if (tty)` branch. - ctrl_lock is held by all writers: By changing __proc_set_tty() to hold the lock a little longer. - All readers that aren't holding tty_lock() hold ctrl_lock: By adding locking to tiocgsid() and __do_SAK(), and expanding the area covered by ctrl_lock in tiocspgrp(). Cc: stable@kernel.org Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Jann Horn
|
882e038d2c |
tty: Fix ->pgrp locking in tiocspgrp()
commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bbd4 ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Fugang Duan
|
bc0cecf96a |
tty: serial: imx: keep console clocks always on
commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream.
For below code, there has chance to cause deadlock in SMP system:
Thread 1:
clk_enable_lock();
pr_info("debug message");
clk_enable_unlock();
Thread 2:
imx_uart_console_write()
clk_enable()
clk_enable_lock();
Thread 1:
Acuired clk enable_lock -> printk -> console_trylock_spinning
Thread 2:
console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock
So the patch is to keep console port clocks always on like
other console drivers.
Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com
Cc: stable <stable@vger.kernel.org>
[fix up build warning - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Qinglang Miao
|
be96acc7c1 |
serial: txx9: add missing platform_driver_unregister() on error in serial_txx9_init
commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream.
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Claire Chang
|
27b5a84801 |
serial: 8250_mtk: Fix uart_get_baud_rate warning
commit 912ab37c798770f21b182d656937072b58553378 upstream.
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Daniel Vetter
|
9421bad22e |
vt: Disable KD_FONT_OP_COPY
commit 3c4e0dff2095c579b142d5a0693257f1c58b4804 upstream. It's buggy: On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote: > We recently discovered a slab-out-of-bounds read in fbcon in the latest > kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that > "fbcon_do_set_font" did not handle "vc->vc_font.data" and > "vc->vc_font.height" correctly, and the patch > <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this > issue. > > Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and > use KD_FONT_OP_SET again to set a large font.height for tty1. After that, > we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data > in "fbcon_do_set_font", while tty1 retains the original larger > height. Obviously, this will cause an out-of-bounds read, because we can > access a smaller vc_font.data with a larger vc_font.height. Further there was only one user ever. - Android's loadfont, busybox and console-tools only ever use OP_GET and OP_SET - fbset documentation only mentions the kernel cmdline font: option, not anything else. - systemd used OP_COPY before release 232 published in Nov 2016 Now unfortunately the crucial report seems to have gone down with gmane, and the commit message doesn't say much. But the pull request hints at OP_COPY being broken https://github.com/systemd/systemd/pull/3651 So in other words, this never worked, and the only project which foolishly every tried to use it, realized that rather quickly too. Instead of trying to fix security issues here on dead code by adding missing checks, fix the entire thing by removing the functionality. Note that systemd code using the OP_COPY function ignored the return value, so it doesn't matter what we're doing here really - just in case a lone server somewhere happens to be extremely unlucky and running an affected old version of systemd. The relevant code from font_copy_to_all_vcs() in systemd was: /* copy font from active VT, where the font was uploaded to */ cfo.op = KD_FONT_OP_COPY; cfo.height = vcs.v_active-1; /* tty1 == index 0 */ (void) ioctl(vcfd, KDFONTOP, &cfo); Note this just disables the ioctl, garbage collecting the now unused callbacks is left for -next. v2: Tetsuo found the old mail, which allowed me to find it on another archive. Add the link too. Acked-by: Peilin Ye <yepeilin.cs@gmail.com> Reported-by: Minh Yuan <yuanmingbuaa@gmail.com> References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html References: https://github.com/systemd/systemd/pull/3651 Cc: Greg KH <greg@kroah.com> Cc: Peilin Ye <yepeilin.cs@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Linus Torvalds
|
0182d680ea |
tty: make FONTX ioctl use the tty pointer they were actually passed
commit 90bfdeef83f1d6c696039b6a917190dcbbad3220 upstream. Some of the font tty ioctl's always used the current foreground VC for their operations. Don't do that then. This fixes a data race on fg_console. Side note: both Michael Ellerman and Jiri Slaby point out that all these ioctls are deprecated, and should probably have been removed long ago, and everything seems to be using the KDFONTOP ioctl instead. In fact, Michael points out that it looks like busybox's loadfont program seems to have switched over to using KDFONTOP exactly _because_ of this bug (ahem.. 12 years ago ;-). Reported-by: Minh Yuan <yuanmingbuaa@gmail.com> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Jiri Slaby <jirislaby@kernel.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Jiri Slaby
|
7f4c966f2a |
vt: keyboard, extend func_buf_lock to readers
commit 82e61c3909db51d91b9d3e2071557b6435018b80 upstream.
Both read-side users of func_table/func_buf need locking. Without that,
one can easily confuse the code by repeatedly setting altering strings
like:
while (1)
for (a = 0; a < 2; a++) {
struct kbsentry kbs = {};
strcpy((char *)kbs.kb_string, a ? ".\n" : "88888\n");
ioctl(fd, KDSKBSENT, &kbs);
}
When that program runs, one can get unexpected output by holding F1
(note the unxpected period on the last line):
.
88888
.8888
So protect all accesses to 'func_table' (and func_buf) by preexisting
'func_buf_lock'.
It is easy in 'k_fn' handler as 'puts_queue' is expected not to sleep.
On the other hand, KDGKBSENT needs a local (atomic) copy of the string
because copy_to_user can sleep. Use already allocated, but unused
'kbs->kb_string' for that purpose.
Note that the program above needs at least CAP_SYS_TTY_CONFIG.
This depends on the previous patch and on the func_buf_lock lock added
in commit 46ca3f735f34 (tty/vt: fix write/write race in ioctl(KDSKBSENT)
handler) in 5.2.
Likely fixes CVE-2020-25656.
Cc: <stable@vger.kernel.org>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201019085517.10176-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
|
Jiri Slaby
|
46edbcd150 |
vt: keyboard, simplify vt_kdgkbsent
commit 6ca03f90527e499dd5e32d6522909e2ad390896b upstream. Use 'strlen' of the string, add one for NUL terminator and simply do 'copy_to_user' instead of the explicit 'for' loop. This makes the KDGKBSENT case more compact. The only thing we need to take care about is NULL 'func_table[i]'. Use an empty string in that case. The original check for overflow could never trigger as the func_buf strings are always shorter or equal to 'struct kbsentry's. Cc: <stable@vger.kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20201019085517.10176-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Peng Fan
|
69a0cf3fb4 |
tty: serial: fsl_lpuart: fix lpuart32_poll_get_char
commit 29788ab1d2bf26c130de8f44f9553ee78a27e8d5 upstream. The watermark is set to 1, so we need to input two chars to trigger RDRF using the original logic. With the new logic, we could always get the char when there is data in FIFO. Suggested-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Tong Zhang
|
3a51df2723 |
tty: ipwireless: fix error handling
[ Upstream commit db332356222d9429731ab9395c89cca403828460 ] ipwireless_send_packet() can only return 0 on success and -ENOMEM on error, the caller should check non zero for error condition Signed-off-by: Tong Zhang <ztong0001@gmail.com> Acked-by: David Sterba <dsterba@suse.com> Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Artem Savkov
|
0fb15ffe75 |
pty: do tty_flip_buffer_push without port->lock in pty_write
[ Upstream commit 71a174b39f10b4b93223d374722aa894b5d8a82e ] b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag" puts tty_flip_buffer_push under port->lock introducing the following possible circular locking dependency: [30129.876566] ====================================================== [30129.876566] WARNING: possible circular locking dependency detected [30129.876567] 5.9.0-rc2+ #3 Tainted: G S W [30129.876568] ------------------------------------------------------ [30129.876568] sysrq.sh/1222 is trying to acquire lock: [30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90 [30129.876572] but task is already holding lock: [30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca [30129.876576] which lock already depends on the new lock. [30129.876577] the existing dependency chain (in reverse order) is: [30129.876578] -> #3 (&pool->lock/1){-.-.}-{2:2}: [30129.876581] _raw_spin_lock+0x30/0x70 [30129.876581] __queue_work+0x1a3/0x10f0 [30129.876582] queue_work_on+0x78/0x80 [30129.876582] pty_write+0x165/0x1e0 [30129.876583] n_tty_write+0x47f/0xf00 [30129.876583] tty_write+0x3d6/0x8d0 [30129.876584] vfs_write+0x1a8/0x650 [30129.876588] -> #2 (&port->lock#2){-.-.}-{2:2}: [30129.876590] _raw_spin_lock_irqsave+0x3b/0x80 [30129.876591] tty_port_tty_get+0x1d/0xb0 [30129.876592] tty_port_default_wakeup+0xb/0x30 [30129.876592] serial8250_tx_chars+0x3d6/0x970 [30129.876593] serial8250_handle_irq.part.12+0x216/0x380 [30129.876593] serial8250_default_handle_irq+0x82/0xe0 [30129.876594] serial8250_interrupt+0xdd/0x1b0 [30129.876595] __handle_irq_event_percpu+0xfc/0x850 [30129.876602] -> #1 (&port->lock){-.-.}-{2:2}: [30129.876605] _raw_spin_lock_irqsave+0x3b/0x80 [30129.876605] serial8250_console_write+0x12d/0x900 [30129.876606] console_unlock+0x679/0xa90 [30129.876606] register_console+0x371/0x6e0 [30129.876607] univ8250_console_init+0x24/0x27 [30129.876607] console_init+0x2f9/0x45e [30129.876609] -> #0 (console_owner){....}-{0:0}: [30129.876611] __lock_acquire+0x2f70/0x4e90 [30129.876612] lock_acquire+0x1ac/0xad0 [30129.876612] console_unlock+0x460/0xa90 [30129.876613] vprintk_emit+0x130/0x420 [30129.876613] printk+0x9f/0xc5 [30129.876614] show_pwq+0x154/0x618 [30129.876615] show_workqueue_state.cold.55+0x193/0x6ca [30129.876615] __handle_sysrq+0x244/0x460 [30129.876616] write_sysrq_trigger+0x48/0x4a [30129.876616] proc_reg_write+0x1a6/0x240 [30129.876617] vfs_write+0x1a8/0x650 [30129.876619] other info that might help us debug this: [30129.876620] Chain exists of: [30129.876621] console_owner --> &port->lock#2 --> &pool->lock/1 [30129.876625] Possible unsafe locking scenario: [30129.876626] CPU0 CPU1 [30129.876626] ---- ---- [30129.876627] lock(&pool->lock/1); [30129.876628] lock(&port->lock#2); [30129.876630] lock(&pool->lock/1); [30129.876631] lock(console_owner); [30129.876633] *** DEADLOCK *** [30129.876634] 5 locks held by sysrq.sh/1222: [30129.876634] #0: ffff8881d3ce0470 (sb_writers#3){.+.+}-{0:0}, at: vfs_write+0x359/0x650 [30129.876637] #1: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: __handle_sysrq+0x4d/0x460 [30129.876640] #2: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: show_workqueue_state+0x5/0xf0 [30129.876642] #3: ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca [30129.876645] #4: ffffffff92c39980 (console_lock){+.+.}-{0:0}, at: vprintk_emit+0x123/0x420 [30129.876648] stack backtrace: [30129.876649] CPU: 3 PID: 1222 Comm: sysrq.sh Tainted: G S W 5.9.0-rc2+ #3 [30129.876649] Hardware name: Intel Corporation 2012 Client Platform/Emerald Lake 2, BIOS ACRVMBY1.86C.0078.P00.1201161002 01/16/2012 [30129.876650] Call Trace: [30129.876650] dump_stack+0x9d/0xe0 [30129.876651] check_noncircular+0x34f/0x410 [30129.876653] __lock_acquire+0x2f70/0x4e90 [30129.876656] lock_acquire+0x1ac/0xad0 [30129.876658] console_unlock+0x460/0xa90 [30129.876660] vprintk_emit+0x130/0x420 [30129.876660] printk+0x9f/0xc5 [30129.876661] show_pwq+0x154/0x618 [30129.876662] show_workqueue_state.cold.55+0x193/0x6ca [30129.876664] __handle_sysrq+0x244/0x460 [30129.876665] write_sysrq_trigger+0x48/0x4a [30129.876665] proc_reg_write+0x1a6/0x240 [30129.876666] vfs_write+0x1a8/0x650 It looks like the commit was aimed to protect tty_insert_flip_string and there is no need for tty_flip_buffer_push to be under this lock. Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag") Signed-off-by: Artem Savkov <asavkov@redhat.com> Acked-by: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20200902120045.3693075-1-asavkov@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Tyrel Datwyler
|
171408e8ed |
tty: hvcs: Don't NULL tty->driver_data until hvcs_cleanup()
[ Upstream commit 63ffcbdad738e3d1c857027789a2273df3337624 ]
The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.
Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().
Fixes: 27bf7c43a19c ("TTY: hvcs, add tty install")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
|
Tong Zhang
|
ee042abcf6 |
tty: serial: earlycon dependency
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
Jonathan Bakker
|
3d01f225c6 |
tty: serial: samsung: Correct clock selection logic
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ] Some variants of the samsung tty driver can pick which clock to use for their baud rate generation. In the DT conversion, a default clock was selected to be used if a specific one wasn't assigned and then a comparison of which clock rate worked better was done. Unfortunately, the comparison was implemented in such a way that only the default clock was ever actually compared. Fix this by iterating through all possible clocks, except when a specific clock has already been picked via clk_sel (which is only possible via board files). Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Wei Yongjun
|
18710ee3a0 |
sparc64: vcc: Fix error return code in vcc_probe()
[ Upstream commit ff62255a2a5c1228a28f2bb063646f948115a309 ] Fix to return negative error code -ENOMEM from the error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20200427122415.47416-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Raviteja Narayanam
|
10f5562478 |
serial: uartps: Wait for tx_empty in console setup
[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ] On some platforms, the log is corrupted while console is being registered. It is observed that when set_termios is called, there are still some bytes in the FIFO to be transmitted. So, wait for tx_empty inside cdns_uart_console_setup before calling set_termios. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Vignesh Raghavendra
|
a94174de44 |
serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeout
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ] Terminate and flush DMA internal buffers, before pushing RX data to higher layer. Otherwise, this will lead to data corruption, as driver would end up pushing stale buffer data to higher layer while actual data is still stuck inside DMA hardware and has yet not arrived at the memory. While at that, replace deprecated dmaengine_terminate_all() with dmaengine_terminate_async(). Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Peter Ujfalusi
|
e8be86c1d2 |
serial: 8250_omap: Fix sleeping function called from invalid context during probe
[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ] When booting j721e the following bug is printed: [ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99 [ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1 [ 1.154832] 3 locks held by kworker/0:1/12: [ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138 [ 1.154872] irq event stamp: 63096 [ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78 [ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80 [ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564 [ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140 [ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221 [ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT) [ 1.154917] Workqueue: events deferred_probe_work_func [ 1.154923] Call trace: [ 1.154928] dump_backtrace+0x0/0x190 [ 1.154933] show_stack+0x14/0x20 [ 1.154940] dump_stack+0xe0/0x148 [ 1.154946] ___might_sleep+0x150/0x1f0 [ 1.154952] __might_sleep+0x4c/0x80 [ 1.154957] wait_for_completion_timeout+0x40/0x140 [ 1.154964] ti_sci_set_device_state+0xa0/0x158 [ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20 [ 1.154977] ti_sci_dev_start+0x34/0x50 [ 1.154984] genpd_runtime_resume+0x78/0x1f8 [ 1.154991] __rpm_callback+0x3c/0x140 [ 1.154996] rpm_callback+0x20/0x80 [ 1.155001] rpm_resume+0x568/0x758 [ 1.155007] __pm_runtime_resume+0x44/0xb0 [ 1.155013] omap8250_probe+0x2b4/0x508 [ 1.155019] platform_drv_probe+0x50/0xa0 [ 1.155023] really_probe+0xd4/0x318 [ 1.155028] driver_probe_device+0x54/0xe8 [ 1.155033] __device_attach_driver+0x80/0xb8 [ 1.155039] bus_for_each_drv+0x74/0xc0 [ 1.155044] __device_attach+0xdc/0x138 [ 1.155049] device_initial_probe+0x10/0x18 [ 1.155053] bus_probe_device+0x98/0xa0 [ 1.155058] deferred_probe_work_func+0x74/0xb0 [ 1.155063] process_one_work+0x280/0x6e8 [ 1.155068] worker_thread+0x48/0x430 [ 1.155073] kthread+0x108/0x138 [ 1.155079] ret_from_fork+0x10/0x18 To fix the bug we need to first call pm_runtime_enable() prior to any pm_runtime calls. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
|
Vignesh Raghavendra
|
a978c01bd6 |
serial: 8250_port: Don't service RX FIFO if throttled
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ] When port's throttle callback is called, it should stop pushing any more data into TTY buffer to avoid buffer overflow. This means driver has to stop HW from receiving more data and assert the HW flow control. For UARTs with auto HW flow control (such as 8250_omap) manual assertion of flow control line is not possible and only way is to allow RX FIFO to fill up, thus trigger auto HW flow control logic. Therefore make sure that 8250 generic IRQ handler does not drain data when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not servicing, RX FIFO would trigger auto HW flow control when FIFO occupancy reaches preset threshold, thus halting RX. Since, error conditions in UART_LSR register are cleared just by reading the register, data has to be drained in case there are FIFO errors, else error information will lost. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Lukas Wunner
|
a351bdff6d |
serial: 8250: Avoid error message on reprobe
commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.
Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
[iwamatsu: Backported to 4.14, 4.19: adjust context]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Tobias Diedrich
|
5ebb9dc9ac |
serial: 8250_pci: Add Realtek 816a and 816b
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Sergey Senozhatsky
|
5026ce65aa |
serial: 8250: change lock order in serial8250_do_startup()
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream. We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Valmer Huhn
|
8284edbf37 |
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
commit c6b9e95dde7b54e6a53c47241201ab5a4035c320 upstream.
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
|
Lukas Wunner
|
fe5d0805aa |
serial: pl011: Don't leak amba_ports entry on driver register error
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
|
Lukas Wunner
|
4ad066160a |
serial: pl011: Fix oops on -EPROBE_DEFER
commit 27afac93e3bd7fa89749cf11da5d86ac9cde4dba upstream.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f12e ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f12e ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Tamseel Shams
|
d1fff1120d |
serial: samsung: Removes the IRQ not found warning
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream. In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following false-positive error: "IRQ index 1 not found" on newer SoC's. This patch adds the condition to check for Tx interrupt only for the those SoC's which have 2 interrupt lines. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
George Kennedy
|
422ef2b827 |
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
commit bc5269ca765057a1b762e79a1cfd267cd7bf1c46 upstream. vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl to save struct vc_data values that are modified and restore the original values in case of error. Signed-off-by: George Kennedy <george.kennedy@oracle.com> Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/1596213192-6635-2-git-send-email-george.kennedy@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Tetsuo Handa
|
47b7a50f8a |
vt: defer kfree() of vc_screenbuf in vc_do_resize()
commit f8d1653daec02315e06d30246cff4af72e76e54e upstream. syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin(). Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access vc->vc_pos when scroll is involved in order to manipulate cursor, but vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets updated based on the result of vc->vc_sw->con_set_origin(). Preserving old buffer and tolerating outdated vc members until set_origin() completes would be easier than preventing vc->vc_sw->con_set_origin() from accessing outdated vc members. [1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3 Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Tetsuo Handa
|
7cecdf9655 |
vt: Reject zero-sized screen buffer size.
commit ce684552a266cb1c7cc2f7e623f38567adec6653 upstream. syzbot is reporting general protection fault in do_con_write() [1] caused by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0 caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate() from con_install() from tty_init_dev() from tty_open() on such console causes vc->vc_pos == 0x10000000e due to ((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1). I don't think that a console with 0 column or 0 row makes sense. And it seems that vc_do_resize() does not intend to allow resizing a console to 0 column or 0 row due to new_cols = (cols ? cols : vc->vc_cols); new_rows = (lines ? lines : vc->vc_rows); exception. Theoretically, cols and rows can be any range as long as 0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g. cols == 1048576 && rows == 2 is possible) because of vc->vc_size_row = vc->vc_cols << 1; vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row; in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate(). Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return an error, and con_write() will not be called on a console with 0 column or 0 row. We need to make sure that integer overflow in visual_init() won't happen. Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying 1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate() will be practically fine. This patch does not touch con_init(), for returning -EINVAL there does not help when we are not returning -ENOMEM. [1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8 Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Serge Semin
|
ead742adb0 |
serial: 8250_mtk: Fix high-speed baud rates clamping
commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream.
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Yang Yingliang
|
c5760ab7aa |
serial: 8250: fix null-ptr-deref in serial8250_start_tx()
commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream. I got null-ptr-deref in serial8250_start_tx(): [ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 78.123778] Mem abort info: [ 78.126560] ESR = 0x86000007 [ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits [ 78.134891] SET = 0, FnV = 0 [ 78.137933] EA = 0, S1PTW = 0 [ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600 [ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000 [ 78.160029] Internal error: Oops: 86000007 [#1] SMP [ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd [ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48 [ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020 [ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--) [ 78.228435] pc : 0x0 [ 78.230618] lr : serial8250_start_tx+0x160/0x260 [ 78.235215] sp : ffff800062eefb80 [ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff [ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000 [ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000 [ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002 [ 78.259679] x21: 0000000000000001 x20: 0000000000000000 [ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000 [ 78.270259] x17: 0000000000000000 x16: 0000000000000000 [ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6 [ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539 [ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0 [ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88 [ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000 [ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8 [ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002 [ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8 [ 78.317873] Call trace: [ 78.320312] 0x0 [ 78.322147] __uart_start.isra.9+0x64/0x78 [ 78.326229] uart_start+0xb8/0x1c8 [ 78.329620] uart_flush_chars+0x24/0x30 [ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30 [ 78.338128] n_tty_receive_buf+0x44/0x2c8 [ 78.342122] tty_ioctl+0x348/0x11f8 [ 78.345599] ksys_ioctl+0xd8/0xf8 [ 78.348903] __arm64_sys_ioctl+0x2c/0xc8 [ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0 [ 78.357583] do_el0_svc+0x44/0xd0 [ 78.360887] el0_sync_handler+0x14c/0x1d0 [ 78.364880] el0_sync+0x140/0x180 [ 78.368185] Code: bad PC value SERIAL_PORT_DFNS is not defined on each arch, if it's not defined, serial8250_set_defaults() won't be called in serial8250_isa_init_ports(), so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref. Fix this problem by calling serial8250_set_defaults() after init uart port. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Matthew Howell
|
7b8d75ae4d |
serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X
[ Upstream commit 5fdbe136ae19ab751daaa4d08d9a42f3e30d17f9 ]
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
Greg Kroah-Hartman
|
f1bd26cf65 |
Revert "tty: hvc: Fix data abort due to race in hvc_open"
commit cf9c94456ebafc6d75a834e58dfdc8ae71a3acbc upstream. This reverts commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe. In discussion on the mailing list, it has been determined that this is not the correct type of fix for this issue. Revert it so that we can do this correctly. Reported-by: Jiri Slaby <jslaby@suse.cz> Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org Cc: Raghavendra Rao Ananta <rananta@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Gregory CLEMENT
|
3fe2c3327e |
tty: n_gsm: Fix bogus i++ in gsm_data_kick
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
|
Gregory CLEMENT
|
5665eea71f |
tty: n_gsm: Fix waking up upper tty layer when room available
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
|
Gregory CLEMENT
|
44c68ccdc8 |
tty: n_gsm: Fix SOF skipping
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
John Stultz
|
44a32bc22d |
serial: amba-pl011: Make sure we initialize the port.lock spinlock
[ Upstream commit 8508f4cba308f785b2fd4b8c38849c117b407297 ] Valentine reported seeing: [ 3.626638] INFO: trying to register non-static key. [ 3.626639] the code is fine but needs lockdep annotation. [ 3.626640] turning off the locking correctness validator. [ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116 [ 3.626646] Hardware name: HiKey960 (DT) [ 3.626656] Workqueue: events deferred_probe_work_func [ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes) [ 3.640220] Call trace: [ 3.640225] dump_backtrace+0x0/0x1b8 [ 3.640227] show_stack+0x20/0x30 [ 3.640230] dump_stack+0xec/0x158 [ 3.640234] register_lock_class+0x598/0x5c0 [ 3.640235] __lock_acquire+0x80/0x16c0 [ 3.640236] lock_acquire+0xf4/0x4a0 [ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8 [ 3.640245] uart_add_one_port+0x388/0x4b8 [ 3.640248] pl011_register_port+0x70/0xf0 [ 3.640250] pl011_probe+0x184/0x1b8 [ 3.640254] amba_probe+0xdc/0x180 [ 3.640256] really_probe+0xe0/0x338 [ 3.640257] driver_probe_device+0x60/0xf8 [ 3.640259] __device_attach_driver+0x8c/0xd0 [ 3.640260] bus_for_each_drv+0x84/0xd8 [ 3.640261] __device_attach+0xe4/0x140 [ 3.640263] device_initial_probe+0x1c/0x28 [ 3.640265] bus_probe_device+0xa4/0xb0 [ 3.640266] deferred_probe_work_func+0x7c/0xb8 [ 3.640269] process_one_work+0x2c0/0x768 [ 3.640271] worker_thread+0x4c/0x498 [ 3.640272] kthread+0x14c/0x158 [ 3.640275] ret_from_fork+0x10/0x1c Which seems to be due to the fact that after allocating the uap structure, nothing initializes the spinlock. Its a little confusing, as uart_port_spin_lock_init() is one place where the lock is supposed to be initialized, but it has an exception for the case where the port is a console. This makes it seem like a deeper fix is needed to properly register the console, but I'm not sure what that entails, and Andy suggested that this approach is less invasive. Thus, this patch resolves the issue by initializing the spinlock in the driver, and resolves the resulting warning. Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-serial@vger.kernel.org Reported-by: Valentin Schneider <valentin.schneider@arm.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Raghavendra Rao Ananta
|
e00eda8c9c |
tty: hvc: Fix data abort due to race in hvc_open
[ Upstream commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe ] Potentially, hvc_open() can be called in parallel when two tasks calls open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add() callback in the function fails, where it sets the tty->driver_data to NULL, the parallel hvc_open() can see this NULL and cause a memory abort. Hence, serialize hvc_open and check if tty->private_data is NULL before proceeding ahead. The issue can be easily reproduced by launching two tasks simultaneously that does nothing but open() and close() on /dev/hvcX. For example: $ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 & Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org> Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
Uwe Kleine-König
|
fcc388ca88 |
serial: imx: Fix handling of TC irq in combination with DMA
commit 1866541492641c02874bf51f9d8712b5510f2c64 upstream. When using RS485 half duplex the Transmitter Complete irq is needed to determine the moment when the transmitter can be disabled. When using DMA this irq must only be enabled when DMA has completed to transfer all data. Otherwise the CPU might busily trigger this irq which is not properly handled and so the also pending irq for the DMA transfer cannot trigger. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [Backport to v4.14] Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Jiri Slaby
|
94d8520821 |
tty: hvc_console, fix crashes on parallel open/close
commit 24eb2377f977fe06d84fca558f891f95bc28a449 upstream. hvc_open sets tty->driver_data to NULL when open fails at some point. Typically, the failure happens in hp->ops->notifier_add(). If there is a racing process which tries to open such mangled tty, which was not closed yet, the process will crash in hvc_open as tty->driver_data is NULL. All this happens because close wants to know whether open failed or not. But ->open should not NULL this and other tty fields for ->close to be happy. ->open should call tty_port_set_initialized(true) and close should check by tty_port_initialized() instead. So do this properly in this driver. So this patch removes these from ->open: * tty_port_tty_set(&hp->port, NULL). This happens on last close. * tty->driver_data = NULL. Dtto. * tty_port_put(&hp->port). This happens in shutdown and until now, this must have been causing a reference underflow, if I am not missing something. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: stable <stable@vger.kernel.org> Reported-and-tested-by: Raghavendra <rananta@codeaurora.org> Link: https://lore.kernel.org/r/20200526145632.13879-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Dmitry Torokhov
|
26079af52b |
vt: keyboard: avoid signed integer overflow in k_ascii
commit b86dab054059b970111b5516ae548efaae5b3aae upstream. When k_ascii is invoked several times in a row there is a potential for signed integer overflow: UBSAN: Undefined behaviour in drivers/tty/vt/keyboard.c:888:19 signed integer overflow: 10 * 1111111111 cannot be represented in type 'int' CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.11 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xce/0x128 lib/dump_stack.c:118 ubsan_epilogue+0xe/0x30 lib/ubsan.c:154 handle_overflow+0xdc/0xf0 lib/ubsan.c:184 __ubsan_handle_mul_overflow+0x2a/0x40 lib/ubsan.c:205 k_ascii+0xbf/0xd0 drivers/tty/vt/keyboard.c:888 kbd_keycode drivers/tty/vt/keyboard.c:1477 [inline] kbd_event+0x888/0x3be0 drivers/tty/vt/keyboard.c:1495 While it can be worked around by using check_mul_overflow()/ check_add_overflow(), it is better to introduce a separate flag to signal that number pad is being used to compose a symbol, and change type of the accumulator from signed to unsigned, thus avoiding undefined behavior when it overflows. Reported-by: Kyungtae Kim <kt0755@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200525232740.GA262061@dtor-ws Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Guoqing Jiang
|
60f4dba707 |
sc16is7xx: move label 'err_spi' to correct section
commit e00164a0f000de893944981f41a568c981aca658 upstream.
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d9901 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Kazuhiro Fujita
|
c7dd89cafd |
serial: sh-sci: Make sure status register SCxSR is read in correct sequence
commit 3dc4db3662366306e54ddcbda4804acb1258e4ba upstream. For SCIF and HSCIF interfaces the SCxSR register holds the status of data that is to be read next from SCxRDR register, But where as for SCIFA and SCIFB interfaces SCxSR register holds status of data that is previously read from SCxRDR register. This patch makes sure the status register is read depending on the port types so that errors are caught accordingly. Cc: <stable@vger.kernel.org> Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com> Signed-off-by: Hao Bui <hao.bui.yg@renesas.com> Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Nicolas Pitre
|
82f66b9dfa |
vt: don't hardcode the mem allocation upper bound
commit 2717769e204e83e65b8819c5e2ef3e5b6639b270 upstream.
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c605 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
|
Jiri Slaby
|
37fe882533 |
tty: rocket, avoid OOB access
commit 7127d24372bf23675a36edc64d092dc7fd92ebe8 upstream.
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Andrew Melnychenko
|
6f7818d90c |
tty: hvc: fix buffer overflow during hvc_alloc().
commit 9a9fc42b86c06120744555fea43fdcabe297c656 upstream. If there is a lot(more then 16) of virtio-console devices or virtio_console module is reloaded - buffers 'vtermnos' and 'cons_ops' are overflowed. In older kernels it overruns spinlock which leads to kernel freezing: https://bugzilla.redhat.com/show_bug.cgi?id=1786239 To reproduce the issue, you can try simple script that loads/unloads module. Something like this: while [ 1 ] do modprobe virtio_console sleep 2 modprobe -r virtio_console sleep 2 done Description of problem: Guest get 'Call Trace' when loading module "virtio_console" and unloading it frequently - clearly reproduced on kernel-4.18.0: [ 81.498208] ------------[ cut here ]------------ [ 81.499263] pvqspinlock: lock 0xffffffff92080020 has corrupted value 0xc0774ca0! [ 81.501000] WARNING: CPU: 0 PID: 785 at kernel/locking/qspinlock_paravirt.h:500 __pv_queued_spin_unlock_slowpath+0xc0/0xd0 [ 81.503173] Modules linked in: virtio_console fuse xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nft_counter nf_nat_tftp nft_objref nf_conntrack_tftp tun bridge stp llc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nf_tables_set nft_chain_nat_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 nft_chain_route_ipv6 nft_chain_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack nft_chain_route_ipv4 ip6_tables nft_compat ip_set nf_tables nfnetlink sunrpc bochs_drm drm_vram_helper ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm i2c_piix4 pcspkr crct10dif_pclmul crc32_pclmul joydev ghash_clmulni_intel ip_tables xfs libcrc32c sd_mod sg ata_generic ata_piix virtio_net libata crc32c_intel net_failover failover serio_raw virtio_scsi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: virtio_console] [ 81.517019] CPU: 0 PID: 785 Comm: kworker/0:2 Kdump: loaded Not tainted 4.18.0-167.el8.x86_64 #1 [ 81.518639] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014 [ 81.520205] Workqueue: events control_work_handler [virtio_console] [ 81.521354] RIP: 0010:__pv_queued_spin_unlock_slowpath+0xc0/0xd0 [ 81.522450] Code: 07 00 48 63 7a 10 e8 bf 64 f5 ff 66 90 c3 8b 05 e6 cf d6 01 85 c0 74 01 c3 8b 17 48 89 fe 48 c7 c7 38 4b 29 91 e8 3a 6c fa ff <0f> 0b c3 0f 0b 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48 [ 81.525830] RSP: 0018:ffffb51a01ffbd70 EFLAGS: 00010282 [ 81.526798] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000 [ 81.528110] RDX: ffff9e66f1826480 RSI: ffff9e66f1816a08 RDI: ffff9e66f1816a08 [ 81.529437] RBP: ffffffff9153ff10 R08: 000000000000026c R09: 0000000000000053 [ 81.530732] R10: 0000000000000000 R11: ffffb51a01ffbc18 R12: ffff9e66cd682200 [ 81.532133] R13: ffffffff9153ff10 R14: ffff9e6685569500 R15: ffff9e66cd682000 [ 81.533442] FS: 0000000000000000(0000) GS:ffff9e66f1800000(0000) knlGS:0000000000000000 [ 81.534914] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 81.535971] CR2: 00005624c55b14d0 CR3: 00000003a023c000 CR4: 00000000003406f0 [ 81.537283] Call Trace: [ 81.537763] __raw_callee_save___pv_queued_spin_unlock_slowpath+0x11/0x20 [ 81.539011] .slowpath+0x9/0xe [ 81.539585] hvc_alloc+0x25e/0x300 [ 81.540237] init_port_console+0x28/0x100 [virtio_console] [ 81.541251] handle_control_message.constprop.27+0x1c4/0x310 [virtio_console] [ 81.542546] control_work_handler+0x70/0x10c [virtio_console] [ 81.543601] process_one_work+0x1a7/0x3b0 [ 81.544356] worker_thread+0x30/0x390 [ 81.545025] ? create_worker+0x1a0/0x1a0 [ 81.545749] kthread+0x112/0x130 [ 81.546358] ? kthread_flush_work_fn+0x10/0x10 [ 81.547183] ret_from_fork+0x22/0x40 [ 81.547842] ---[ end trace aa97649bd16c8655 ]--- [ 83.546539] general protection fault: 0000 [#1] SMP NOPTI [ 83.547422] CPU: 5 PID: 3225 Comm: modprobe Kdump: loaded Tainted: G W --------- - - 4.18.0-167.el8.x86_64 #1 [ 83.549191] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014 [ 83.550544] RIP: 0010:__pv_queued_spin_lock_slowpath+0x19a/0x2a0 [ 83.551504] Code: c4 c1 ea 12 41 be 01 00 00 00 4c 8d 6d 14 41 83 e4 03 8d 42 ff 49 c1 e4 05 48 98 49 81 c4 40 a5 02 00 4c 03 24 c5 60 48 34 91 <49> 89 2c 24 b8 00 80 00 00 eb 15 84 c0 75 0a 41 0f b6 54 24 14 84 [ 83.554449] RSP: 0018:ffffb51a0323fdb0 EFLAGS: 00010202 [ 83.555290] RAX: 000000000000301c RBX: ffffffff92080020 RCX: 0000000000000001 [ 83.556426] RDX: 000000000000301d RSI: 0000000000000000 RDI: 0000000000000000 [ 83.557556] RBP: ffff9e66f196a540 R08: 000000000000028a R09: ffff9e66d2757788 [ 83.558688] R10: 0000000000000000 R11: 0000000000000000 R12: 646e61725f770b07 [ 83.559821] R13: ffff9e66f196a554 R14: 0000000000000001 R15: 0000000000180000 [ 83.560958] FS: 00007fd5032e8740(0000) GS:ffff9e66f1940000(0000) knlGS:0000000000000000 [ 83.562233] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 83.563149] CR2: 00007fd5022b0da0 CR3: 000000038c334000 CR4: 00000000003406e0 Signed-off-by: Andrew Melnychenko <andrew@daynix.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200414191503.3471783-1-andrew@daynix.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
Stephen Rothwell
|
bcc576e551 |
tty: evh_bytechan: Fix out of bounds accesses
commit 3670664b5da555a2a481449b3baafff113b0ac35 upstream.
ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.
There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.
The warnings (from a powerpc allyesconfig build) are:
In file included from include/linux/byteorder/big_endian.h:5,
from arch/powerpc/include/uapi/asm/byteorder.h:14,
from include/asm-generic/bitops/le.h:6,
from arch/powerpc/include/asm/bitops.h:250,
from include/linux/bitops.h:29,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/powerpc/include/asm/bug.h:109,
from include/linux/bug.h:5,
from include/linux/mmdebug.h:5,
from include/linux/gfp.h:5,
from include/linux/slab.h:15,
from drivers/tty/ehv_bytechan.c:24:
drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
298 | r6 = be32_to_cpu(p[1]);
include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
| ^
arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
298 | r6 = be32_to_cpu(p[1]);
| ^~~~~~~~~~~
drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
166 | static void ehv_bc_udbg_putc(char c)
| ^~~~~~~~~~~~~~~~
Fixes: dcd83aaff1c8 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
||
Eric Biggers
|
ebba196c39 |
vt: vt_ioctl: fix use-after-free in vt_in_use()
commit 7cf64b18b0b96e751178b8d0505d8466ff5a448f upstream.
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|