[ Upstream commit 4ad26f117b6ea0f5d5f1592127bafb5ec65904d3 ]
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 308c6cafde0147616da45e3a928adae55c428deb ]
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1d4be681b2c26fd874adbf584bf034573ac45d ]
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51367e423c6501a26e67d91a655d2bc892303462 ]
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab4c3426c0cf711d7147e3f559638e4ab88960e ]
Clang warns:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c629421a990033ba539eb8585e73a2e6fa9ea631 ]
Need to be able to boot without PCI devices present.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801df68d617e3cb831f531c99fa6003620e6b343 ]
csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9061193c4ee065d3240fde06767c2e06ec61decc ]
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04f05230c5c13b1384f66f5186a68d7499e34622 ]
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf666c1af916ed74795493c564df6fad462cc80 ]
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 708abf74dd87f8640871b814faa195fb5970b0e3 ]
In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.
Fixes: 45040978c899 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 158daed16efb1170694e420ae06ba8ba954d82e5 ]
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca0c ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16877a5570e0c5f4270d5b17f9bab427bcae9514 ]
There is a guard hole at the beginning of the kernel address space, also
used by hypervisors. It occupies 16 PGD entries.
This reserved range is not defined explicitely, it is calculated relative
to other entities: direct mapping and user space ranges.
The calculation got broken by recent changes of the kernel memory layout:
LDT remap range is now mapped before direct mapping and makes the
calculation invalid.
The breakage leads to crash on Xen dom0 boot[1].
Define the reserved range explicitely. It's part of kernel ABI (hypervisors
expect it to be stable) and must not depend on changes in the rest of
kernel memory layout.
[1] https://lists.xenproject.org/archives/html/xen-devel/2018-11/msg03313.html
Fixes: d52888aa2753 ("x86/mm: Move LDT remap out of KASLR region on 5-level paging")
Reported-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: bhe@redhat.com
Cc: linux-mm@kvack.org
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20181130202328.65359-2-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e41cae64b08fe2e86a9ffb88b295c6b4b3a3322 ]
gcc warning this:
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca5047286c9c93a01e1f471d00a6019536992954 ]
Before commit 7fd6d98b89f3 ("i2c: i801: Allow ACPI AML access I/O
ports not reserved for SMBus"), enabling RMI on the T560 would cause
the touchpad to stop working after resuming from suspend. Now that
this issue is fixed, RMI can be enabled safely and works fine.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2ca26ec4f01486661b55b03597c13e2b9c18b73 ]
With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.
From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae4f8420ed7be4b13c96600e3568c144d101a23 ]
If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.
Fixes: aea71a024914 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530aad77010b81526586dfc09130ec875cd084e4 ]
When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.
This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.
This bug pre-dates git history.
Reported-by: Neel Mehta <nmehta@google.com>
Reported-by: Shane Huntley <shuntley@google.com>
Reported-by: Heather Adkins <argv@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0152eee6fc3b84298bb6a79961961734e8afa5b8 ]
Since commit 222d7dbd258d ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code doesn't expect this to happen, so we crash with
a NULL pointer dereference in this case.
Fix it by checking skb_dst(skb) for NULL after skb_dst_force()
and drop the packet in case the dst_entry was cleared. We also
move the skb_dst_force() to a codepath that is not used when
the transformation was offloaded, because in this case we
don't have a dst_entry attached to the skb.
The output and forwarding path was already fixed by
commit 9e1437937807 ("xfrm: Fix NULL pointer dereference when
skb_dst_force clears the dst_entry.")
Fixes: 222d7dbd258d ("net: prevent dst uses after free")
Reported-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca92e173ab34a4f7fc4128bd372bd96f1af6f507 ]
sadhcnt is reported by `ip -s xfrm state count` as "buckets count", not the
hash mask.
Fixes: 28d8909bc790 ("[XFRM]: Export SAD info.")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533555e5cbb6aa2d77598917871ae5b579fe724b ]
xfrm_output_one() does not return a error code when there is
no dst_entry attached to the skb, it is still possible crash
with a NULL pointer dereference in xfrm_output_resume(). Fix
it by return error code -EHOSTUNREACH.
Fixes: 9e1437937807 ("xfrm: Fix NULL pointer dereference when skb_dst_force clears the dst_entry.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1733a1d3cd32a9492f4cf866be37bb46e10163d ]
There is actually a space after "sp," like this,
ffff2000080813c8: a9bb7bfd stp x29, x30, [sp, #-80]!
Right now, checkstack.pl isn't able to print anything on aarch64,
because it won't be able to match the stating objdump line of a function
due to this missing space. Hence, it displays every stack as zero-size.
After this patch, checkpatch.pl is able to match the start of a
function's objdump, and is then able to calculate each function's stack
correctly.
Link: http://lkml.kernel.org/r/20181207195843.38528-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c201e3808e0e4be9b98d192802085a9f491bd80c ]
ABS_RESERVED was added in d9ca1c990a7 and accidentally removed as part of
ffe0e7cf290f5c9 when the high-resolution scrolling code was removed.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f15096f12a4e9340168df5fdd9201aa8ed60d59e ]
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e434b703248580b7aaaf8a115d93e682f57d29f ]
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4050207485e47e00353e87f2fe2166083e282688 ]
The 258a:6a88 keyboard-dock shipped with the Prowise PT301 tablet is
likely another ITE based design. The controller die is directly bonded
to the PCB with a blob of black glue on top so there are no markings and
the 258a vendor-id used is unknown anywhere. But the keyboard has the
exact same hotkeys mapped to Fn+F1 - F10 as the other ITE8595 keyboard
I have *and* it has the same quirky behavior wrt the rfkill hotkey.
Either way as said this keyboard has the same quirk for its rfkill /
airplane mode hotkey as the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds the 258a:6a88 USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 462951cd32e1496dc64b00051dfb777efc8ae5d8 ]
For some configs the build fails with:
arch/powerpc/mm/dump_linuxpagetables.c: In function 'populate_markers':
arch/powerpc/mm/dump_linuxpagetables.c:306:39: error: 'PKMAP_BASE' undeclared (first use in this function)
arch/powerpc/mm/dump_linuxpagetables.c:314:50: error: 'LAST_PKMAP' undeclared (first use in this function)
These come from highmem.h, including that fixes the build.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5564597d51c8ff5b88d95c76255e18b13b760879 ]
Commit 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper
as a relocatable ET_DYN", 2011-04-12) changed the procedure descriptor
at the start of crt0.S to have a hard-coded start address of 0x500000
rather than a reference to _zimage_start, presumably because having
a reference to a symbol introduced a relocation which is awkward to
handle in a position-independent executable. Unfortunately, what is
at 0x500000 in the COFF image is not the first instruction, but the
procedure descriptor itself, that is, a word containing 0x500000,
which is not a valid instruction. Hence, booting a COFF zImage
results in a "DEFAULT CATCH!, code=FFF00700" message from Open
Firmware.
This fixes the problem by (a) putting the procedure descriptor in the
data section and (b) adding a branch to _zimage_start as the first
instruction in the program.
Fixes: 6975a783d7b4 ("powerpc/boot: Allow building the zImage wrapper as a relocatable ET_DYN")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 614b1868a125a0ba24be08f3a7fa832ddcde6bca ]
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd8206a ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 66a4059ba72c23ae74a7c702894ff76c4b7eac1f upstream.
MIPS' asm/mmzone.h includes the machine/platform mmzone.h
unconditionally, but since commit bb53fdf395ee ("MIPS: c-r4k: Add
r4k_blast_scache_node for Loongson-3") is included by asm/rk4cache.h for
all r4k-style configs regardless of CONFIG_NEED_MULTIPLE_NODES.
This is problematic when CONFIG_NEED_MULTIPLE_NODES=n because both the
loongson3 & ip27 mmzone.h headers unconditionally define the NODE_DATA
preprocessor macro which is aready defined by linux/mmzone.h, resulting
in the following build error:
In file included from ./arch/mips/include/asm/mmzone.h:10,
from ./arch/mips/include/asm/r4kcache.h:23,
from arch/mips/mm/c-r4k.c:33:
./arch/mips/include/asm/mach-loongson64/mmzone.h:48: error: "NODE_DATA" redefined [-Werror]
#define NODE_DATA(n) (&__node_data[(n)]->pglist)
In file included from ./include/linux/topology.h:32,
from ./include/linux/irq.h:19,
from ./include/asm-generic/hardirq.h:13,
from ./arch/mips/include/asm/hardirq.h:16,
from ./include/linux/hardirq.h:9,
from arch/mips/mm/c-r4k.c:11:
./include/linux/mmzone.h:907: note: this is the location of the previous definition
#define NODE_DATA(nid) (&contig_page_data)
Resolve this by only including the machine mmzone.h when
CONFIG_NEED_MULTIPLE_NODES=y, which also removes the need for the empty
mach-generic version of the header which we delete.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: bb53fdf395ee ("MIPS: c-r4k: Add r4k_blast_scache_node for Loongson-3")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01f54664a4db0d612de0ece8e0022f21f9374e9b upstream.
First, rename out_no_locality to out_locality for bailing out on
both tpm_cmd_ready() and tpm_request_locality() failure.
Second, ignore the return value of go_to_idle() as it may override
the return value of the actual tpm operation, the go_to_idle() error
will be caught on any consequent command.
Last, fix the wrong 'goto out', that jumped back instead of forward.
Cc: stable@vger.kernel.org
Fixes: 627448e85c76 ("tpm: separate cmd_ready/go_idle from runtime_pm")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cc9ffbb1f51eb4320575a48e4805a8f52e0e26b upstream.
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c3e ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726eb ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 9c6dfed92c3e ("rtc: m41t80: add alarm functionality")
References: 48e9766726eb ("drivers/rtc/rtc-m41t80.c: remove disabled alarm functionality")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 107352a24900fb458152b92a4e72fbdc83fd5510 upstream.
We currently only halt the guest when a vCPU messes with the active
state of an SPI. This is perfectly fine for GICv2, but isn't enough
for GICv3, where all vCPUs can access the state of any other vCPU.
Let's broaden the condition to include any GICv3 interrupt that
has an active state (i.e. all but LPIs).
Cc: stable@vger.kernel.org
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df655b75c43fba0f2621680ab261083297fd6d16 upstream.
Although bit 31 of VTCR_EL2 is RES1, we inadvertently end up setting all
of the upper 32 bits to 1 as well because we define VTCR_EL2_RES1 as
signed, which is sign-extended when assigning to kvm->arch.vtcr.
Lucky for us, the architecture currently treats these upper bits as RES0
so, whilst we've been naughty, we haven't set fire to anything yet.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a596f5b39593414c0ec80f71b94a226286f084e upstream.
While resolving a bug with locks on samba shares found a strange behavior.
When a file locked by one node and we trying to lock it from another node
it fail with errno 5 (EIO) but in that case errno must be set to
(EACCES | EAGAIN).
This isn't happening when we try to lock file second time on same node.
In this case it returns EACCES as expected.
Also this issue not reproduces when we use SMB1 protocol (vers=1.0 in
mount options).
Further investigation showed that the mapping from status_to_posix_error
is different for SMB1 and SMB2+ implementations.
For SMB1 mapping is [NT_STATUS_LOCK_NOT_GRANTED to ERRlock]
(See fs/cifs/netmisc.c line 66)
but for SMB2+ mapping is [STATUS_LOCK_NOT_GRANTED to -EIO]
(see fs/cifs/smb2maperror.c line 383)
Quick changes in SMB2+ mapping from EIO to EACCES has fixed issue.
BUG: https://bugzilla.kernel.org/show_bug.cgi?id=201971
Signed-off-by: Georgy A Bystrenin <gkot@altlinux.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edefae94b7b9f10d5efe32dece5a36e9d9ecc29e upstream.
Commit 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx
interface detection") added RGMII interface detection for OCTEON III,
but it results in the following logs:
[ 7.165984] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
[ 7.173017] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
The current RGMII routines are valid only for older OCTEONS that
use GMX/ASX hardware blocks. On later chips AGL should be used,
but support for that is missing in the mainline. Until that is added,
mark the interface as disabled.
Fixes: 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx interface detection")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff4dd232ec45a0e45ea69f28f069f2ab22b4908a upstream.
ASIDs have always been stored as unsigned longs, ie. 32 bits on MIPS32
kernels. This is problematic because it is feasible for the ASID version
to overflow & wrap around to zero.
We currently attempt to handle this overflow by simply setting the ASID
version to 1, using asid_first_version(), but we make no attempt to
account for the fact that there may be mm_structs with stale ASIDs that
have versions which we now reuse due to the overflow & wrap around.
Encountering this requires that:
1) A struct mm_struct X is active on CPU A using ASID (V,n).
2) That mm is not used on CPU A for the length of time that it takes
for CPU A's asid_cache to overflow & wrap around to the same
version V that the mm had in step 1. During this time tasks using
the mm could either be sleeping or only scheduled on other CPUs.
3) Some other mm Y becomes active on CPU A and is allocated the same
ASID (V,n).
4) mm X now becomes active on CPU A again, and now incorrectly has the
same ASID as mm Y.
Where struct mm_struct ASIDs are represented above in the format
(version, EntryHi.ASID), and on a typical MIPS32 system version will be
24 bits wide & EntryHi.ASID will be 8 bits wide.
The length of time required in step 2 is highly dependent upon the CPU &
workload, but for a hypothetical 2GHz CPU running a workload which
generates a new ASID every 10000 cycles this period is around 248 days.
Due to this long period of time & the fact that tasks need to be
scheduled in just the right (or wrong, depending upon your inclination)
way, this is obviously a difficult bug to encounter but it's entirely
possible as evidenced by reports.
In order to fix this, simply extend ASIDs to 64 bits even on MIPS32
builds. This will extend the period of time required for the
hypothetical system above to encounter the problem from 28 days to
around 3 trillion years, which feels safely outside of the realms of
possibility.
The cost of this is slightly more generated code in some commonly
executed paths, but this is pretty minimal:
| Code Size Gain | Percentage
-----------------------|----------------|-------------
decstation_defconfig | +270 | +0.00%
32r2el_defconfig | +652 | +0.01%
32r6el_defconfig | +1000 | +0.01%
I have been unable to measure any change in performance of the LMbench
lat_ctx or lat_proc tests resulting from the 64b ASIDs on either
32r2el_defconfig+interAptiv or 32r6el_defconfig+I6500 systems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: James Hogan <jhogan@kernel.org>
References: https://lore.kernel.org/linux-mips/80B78A8B8FEE6145A87579E8435D78C30205D5F3@fzex.ruijie.com.cn/
References: https://lore.kernel.org/linux-mips/1488684260-18867-1-git-send-email-jiwei.sun@windriver.com/
Cc: Jiwei Sun <jiwei.sun@windriver.com>
Cc: Yu Huabing <yhb@ruijie.com.cn>
Cc: stable@vger.kernel.org # 2.6.12+
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bec0de4cfad21bd284dbddee016ed1767a5d2823 upstream.
KEXEC needs the new kernel's load address to be aligned on a page
boundary (see sanity_check_segment_list()), but on MIPS the default
vmlinuz load address is only explicitly aligned to 16 bytes.
Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase
the alignment calculated by calc_vmlinuz_load_addr to 64KB.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21131/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: <stable@vger.kernel.org> # 2.6.36+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb53fdf395eed103f85061bfff3b116cee123895 upstream.
For multi-node Loongson-3 (NUMA configuration), r4k_blast_scache() can
only flush Node-0's scache. So we add r4k_blast_scache_node() by using
(CAC_BASE | (node_id << NODE_ADDRSPACE_SHIFT)) instead of CKSEG0 as the
start address.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paul.burton@mips.com: Include asm/mmzone.h from asm/r4kcache.h for
nid_to_addrbase(). Add asm/mach-generic/mmzone.h
to allow inclusion for all platforms.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21129/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adcc81f148d733b7e8e641300c5590a2cdc13bf3 upstream.
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: stable@vger.kernel.org # v4.8+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rich Felker <dalias@libc.org>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f71a27fa12c1a1b02ad478a568e76260f1815e upstream.
text[s] is a signed char, so using that as index into the font8x16 array
can result in negative indices. Cast it to u8 to be safe.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+ccf0a61ed12f2a7313ee@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.7 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 560ccb75c2caa6b1039dec1a53cd2ef526f5bf03 upstream.
When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+0cc8e3cc63ca373722c6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
