Mainly for use in debugging and benchmarking, this file allows the user
to control the max frequency used by the GPU. Frequency may still vary
based on workload (if the frequency is set to higher than the minimum)
but won't go over the newly set value.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Dell OptiPlex FX170 claims to have LVDS, but doesn't.
Signed-off-by: Pieterjan Camerlynck <pieterjan.camerlynck@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake and above, we have per-transcoder DIP registers, so use them
for sending DIPs like AVI infoframes on ILK and above.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 885a50147f00a8a80108904bf58a18af357717f3.
We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.
However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This describes the function better, allowing it to be used where the
DPCD value is relevant.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.
Signed-off-by: Keith Packard <keithp@keithp.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (135 commits)
drm/radeon/kms: fix DP training for DPEncoderService revision bigger than 1.1
drm/radeon/kms: add missing vddci setting on NI+
drm/radeon: Add a rmb() in IH processing
drm/radeon: ATOM Endian fix for atombios_crtc_program_pll()
drm/radeon: Fix the definition of RADEON_BUF_SWAP_32BIT
drm/radeon: Do an MMIO read on interrupts when not uisng MSIs
drm/radeon: Writeback endian fixes
drm/radeon: Remove a bunch of useless _iomem casts
drm/gem: add support for private objects
DRM: clean up and document parsing of video= parameter
DRM: Radeon: Fix section mismatch.
drm: really make debug levels match in edid failure code
drm/radeon/kms: fix i2c map for rv250/280
drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
drm/nouveau: pass flag to engine fini() method on suspend
drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
drm/nv40/gr: rewrite/split context takedown functions
drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
drm/nouveau: Add a quirk for Gigabyte NX86T
...
DPEncoderService newer than 1.1 can't properly program the DP (display port)
link training. When facing such version use the DIGxEncoderControl method
instead. Fix DP link training on some R7XX.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to add vddci setting to pm init as well as
resume. Fixes hangs on load on some boards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38754
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
The docs say the port has to come on in training pattern 1; at this
point, though, ->DP is in normal mode. The intent here is to wait
until the port is in fact sending data, but that doesn't happen since
we've broken the sequence the hardware expects, and the vblank wait will
time out and kvetch in the log.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The DP spec says training patterns 1 and 2 are to be sent non-scrambled,
and the GPU docs claim that happens (or at least, there's no explicit
scrambling control). But the sink may be confused if we don't
explicitly tell it what we're doing, so play it safe.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Consider a 1600x900 panel, upscaling a 1360x768 mode, full-aspect. The
old math would give you:
scaled_width = 1600 * 768; /* 1228800 */
scaled_height = 1360 * 900; /* 1224000 */
if (scaled_width > scaled_height) { /* pillarbox, and true */
width = 1224000 / 768; /* int(1593.75) = 1593 */
x = (1600 - 1593 + 1) / 2; /* 4 */
y = 0;
height = 768;
} /* ... */
This is broken. The total width of scanout would then be 1593 + 4 + 4,
or 1601, which is wider than the panel itself. The hardware very
dutifully implements this, and you end up with a black 45° diagonal from
the top-left corner to the bottom edge of the screen. It's a cool
effect and all, but not what you wanted. Similar things happen for the
letterbox case.
The problem is that you have an integer number of pixels, which means
it's usually impossible to upscale equally on both axes. 1360/768 is
1.7708, 1600/900 is 1.7777. Since we're constrained on the one axis,
the other one wants to come out as an even number of pixels (the panel
is almost certainly even on both axes, and the x/y offsets will be
applied on both sides). In the math above, if 'width' comes out even,
rounding down is correct; if it's odd, you'd rather round up. So just
increment width/height in those cases.
Tested on a Lenovo T500 (Ironlake).
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Daniel Manrique <daniel.manrique@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38851
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Hotplug detection is a mode setting operation and must hold the
struct_mutex or risk colliding with other mode setting operations.
In particular, the display port hotplug function attempts to re-train
the link if the monitor is supposed to be running when plugged back
in. If that happens while mode setting is underway, the link will get
scrambled, leaving it in an inconsistent state.
This is a special case -- usually the driver mode setting entry points
are covered by the upper level DRM code, but in this case the function
is invoked as a work function not under the control of DRM.
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
It's not clear what a sink would do if you wrote zero to this register -
which I guess would mean "I don't support any channel encodings, good
luck" - but let's not find out.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
%hx alone prints 0 as "0", not "00".
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
For parity with radeon and nouveau, and also because I suspect we're
going to need it to get format-conversion dongles right.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
No reason not to see this on g4x, after all.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We should have a read memory barrier between reading the WPTR from
memory and reading ring entries based on that value (ie, we need to
ensure both loads are done in order by the CPU).
It could be argued that the MMIO reads in r600_ack_irq() might be
enough to get that barrier but I prefer keeping an explicit one just
in case.
[airlied: fix evergreen + r/w mixup]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v6 of the structure was programmed incorrectly:
args.v6.ulCrtcPclkFreq.ulPixelClock = cpu_to_le32(clock / 10);
ulPixelClock is a 24-bit bitfield. This statement would thus
do a 32-bit swap of (clock / 10) and drop the top 8 bits which
are ... the LSB. Not what we want. Instead use masks & shifts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(Note that this is duplicated under various other names such
as R600_BUF_SWAP_32BIT etc...). At least now all the definitions
agree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When not using MSIs, there is no guarantee that DMA from the device
has been fully flushed to point where it's visible to the CPU when
taking an interrupt. To get this guarantee, we need to perform an
MMIO read from the device, which will flush all outstanding DMAs
from bridges between the device and the system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The writeback ring pointer and IH ring pointer are read using le32_to_cpu
so we do not want the chip to byteswap them on big-endian.
We still want to byteswap the ring itself and the IBs, so we don't touch
that but we remove setting of the byteswap bits in CP_RB_RPTR_ADDR and
IH_CNTL.
In general, for things like that where we control all the accessors easily,
we are better off doing the swap in SW rather than HW. Paradoxally, it does
keep the code closer to x86 and avoid using poorly tested HW features.
I also changed the use of RADEON_ to R600_ in a couple of cases to be more
consistent with the surrounding code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just defining rdev->rmmio properly in the first place should do
the trick. In some cases, the cast were also complete dups as
the original variable was already of the right type.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These small changes should allow GEM to be used with non shmem objects as
well as shmem objects. In the GMA500 case it allows the base framebuffer to
appear as a GEM object and thus acquire a handle and work with KMS.
For i915 it ought to be trivial to get back the wasted memory but putting the
system fb back into stolen RAM and in general I can imagine it allowing the
use of GEM and thus KMS with all the older cards that have their framebuffer
firmly placed in video RAM.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The video= parameter of the DRM drivers supports some additional flags that
the normal fb drivers do not have. They also allow to limit these flags to
specific outputs. Both things were previously undocumented.
Also the parsing of the line had some oddities:
-A lot of misplaced options were silently ignored or partly rejected instead
of stopping the parsing immediately
-The 'R' option is documented to follow the 'M' option if specified. It is not
documented that 'M' is needed to specify 'R' (also this is the case for normal
fb drivers). In fact the code is correct for normal fb drivers but wrong for
DRM ones.
The old code allowed 'R' only _before_ 'M' (since it parses backwards) and only
if 'M' is given at all which is not needed for the DRM drivers.
-the margins option ('m') was parsed but later ignored even if the later
functions support it.
-specifying multiple enable options at the same time did not lead to an error.
-specifying something bogus for horizontal resolution (i.e. other things as
digits) did not lead to an error but an invalid resolution was used.
If any errors are encountered the position of the faulting string is now
printed to the user and the complete mode is ignored. This gives much
more consistent error behaviour.
I also removed some useless assignments and changed the local flag variables
to be bool.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
WARNING: drivers/gpu/drm/radeon/radeon.o(.text+0x5d1fc): Section mismatch in reference from the function radeon_get_clock_info() to the function .devinit.text:radeon_read_clocks_OF()
The function radeon_get_clock_info() references
the function __devinit radeon_read_clocks_OF().
This is often because radeon_get_clock_info lacks a __devinit
annotation or the annotation of radeon_read_clocks_OF is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also disable the ascii dump and remove the literal printing of the
KERN_ERR macro in the log:
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
v2: Remove the trailing empty line as well.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
drm/nouveau: pass flag to engine fini() method on suspend
drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
drm/nv40/gr: rewrite/split context takedown functions
drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
drm/nouveau: Add a quirk for Gigabyte NX86T
drm/nouveau: do not leak in nv20_graph_create
drm/nv50/dp: fix hack to work for macbooks booted via EFI
It may not be necessary to fail in certain cases (such as failing to idle)
on module unload, whereas on suspend it's important to ensure a consistent
state can be restored on resume.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
