Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few bugs in the samsung serial driver when built as a
loadable module, which makes the console code unavailable, as well as
giving no access to the 'printascii' early debug function. This adds
the appropriate compile time conditionals.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The registers for the Samsung S3C serial port are currently defined in
the platform specific arch/arm/plat-samsung/include/plat/regs-serial.h
file, which is not visible to multiplatform capable drivers.
Unfortunately, it is not possible to move the file into a more local
place as we should normally try to, because the same registers
may be used in one of four places:
* In the driver itself
* In platform-independent ARM code for early debug output
* In platform_data definitions
* In the Samsung platform power management code
I have also found no way to logically split out a platform_data
file, other than possibly move everything into
include/linux/platform_data, which also felt wrong. The only
part of this file that makes sense to keep specific to the s3c24xx
platform are the virtual and physical addresses defined here,
which are needed in no other location.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the common clock interface, there is no way to provide the
"clock_source" sysfs attribute for the samsung serial ports. Given that
this file was purely informational and had fixed contents, we have reason
to believe that no user space programs were relying on it.
The sysfs file is not documented in the ABI docs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following patch will fix build error if CONFIG_DMA_ENGINE is unset.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The no_console_suspend option allows the console to write to the UART
during early resume, before the serial port itself is resumed. Such
writes hang indefinitely waiting for TX ready.
This adds a check to the console putchar function to drop characters
instead of hanging if the port hasn't been initialized. That way, we
can use no_console_suspend without risk of hanging.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This closes a window where the system may hang in resume as soon as the
UART interrupt is enabled and before the mask is restored. The hang occurs
because the driver can't handle IRQs it thinks are masked.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the interrupt mask register is not preserved across system suspend
and it defaults to all interrupts enabled, it is not enough to disable
UART interrupt.
This patch adds free_irq to port shutdown and mask setting to port
startup to handle IRQ disabling in a suspend-friendly way. In addition,
a bug caused by multiple request_irq calls in port startup callback is
fixed.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the 8250
driver accidentally in the 3.7 kernel release, without realizing that there
were users of the module options that suddenly broke. This is now resolved,
and, to top the injury off, we have a backwards-compatible option for those
users who got used to the new name since 3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been reported by
users.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFUdtEACgkQMUfUDdst+ylklACgx47C3qGEXaPiu6yh3W/D/x97
N1kAoMICQC6K1O1Nge3J5uqbNmYDP6Bv
=wO2Z
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the
8250 driver accidentally in the 3.7 kernel release, without realizing
that there were users of the module options that suddenly broke. This
is now resolved, and, to top the injury off, we have a backwards-
compatible option for those users who got used to the new name since
3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been
reported by users."
* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Xilinx: ARM: UART: clear pending irqs before enabling irqs
TTY: 8250, deprecated 8250_core.* options
TTY: 8250, revert module name change
serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
tty: atmel_serial_probe(): index of atmel_ports[] fix
Consider a situation where I have an ARM based system
and therefore no legacy ports. Say, I have two
memory-mapped ports. I use device tree to describe the
ports. What would be the config options I set so that
I get only the two ports in my system? I do not want
legacy ports being created automatically and I want
it to be flexible enough that it creates the devices
based only on the device tree. I expected setting
SERIAL_8250_RUNTIME_UARTS = 0 to work because the
description said, "Set this to the maximum number of
serial ports you want the kernel to register at boot
time." Unfortunately, even though SERIAL_8250_NR_UARTS
was set to the default value of 4, I did not get any device
nodes (because SERIAL_8250_RUNTIME_UARTS was 0). This
is what this change is addressing.
SERIAL_8250_NR_UARTS controls the maximum number of ports
you can support. SERIAL_8250_RUNTIME_UARTS specifies the
number of ports you want to create automatically for legacy
ports at boot time. All other ports will be created
when serial8250_register_port is called (and if does not exceed
the total number of supported ports as specified by
SERIAL_8250_NR_UARTS).
Signed-off-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for the WindRiver SBC8560 board was removed in v3.6. But there
are still a few lines depending on its obsolete Kconfig macro. Remove
these now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic Flow Control capability is not tied to this
property. This is only one way of detecting it. The property
is limited to be used only with 8250 driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Boot ROM has an issue which will cause the driver to
lock up as pending irqs are not being cleared. With them
cleared it prevents that issue.
This patch is needed for the current (3.9-rc3) mainline kernel. I guess
it went unnoticed, because it was only tested with u-boot up until now.
And u-boot maybe handles this.
[s.trumtrar@pengutronix.de: cherry-picked from linux-xlnx.git]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They were introduced by mistake in 3.7. Let's deprecate them now. For
the reasons, see the text in Kconfig below.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d1a28efba81d5aca7385e24c29d3a6db2
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9e480c3db3bad0c25c590a5d11b31f4ef
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).
That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.
Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datesheet clearly states, that writing low bits to the
XUARTPS_IDR register have no effect. Remove the write.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for SH7367 and SH7377 got removed in v3.8. Now remove their
last Kconfig macros.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will reduce the need for extra types in 8250.c just
in case the fifo size differs from the standard.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the tx_loadsz is the same as fifosize. This
will store the fifosize in it if it was not separately
delivered from the driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc fixes from David Miller:
"Just some minor fixups, a sunsu console setup panic cure, and
recognition of a Fujitsu sun4v cpu."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove unused "config BITS"
sparc: delete "if !ULTRA_HAS_POPULATION_COUNT"
sparc64: correctly recognize SPARC64-X chips
sparc,leon: fix GRPCI2 device0 PCI config space access
sunsu: Fix panic in case of nonexistent port at "console=ttySY" cmdline option
The following commits:
* 6732c8bb8671acbdac6cdc93dd72ddd581dd5e25 (TTY: switch
tty_schedule_flip)
* 2e124b4a390ca85325fae75764bef92f0547fa25 (TTY: switch
tty_flip_buffer_push)
* 05c7cd39907184328f48d3e7899f9cdd653ad336 (TTY: switch
tty_insert_flip_string)
* 92a19f9cec9a80ad93c06e115822deb729e2c6ad (TTY: switch
tty_insert_flip_char)
* 227434f8986c3827a1faedd1feb437acd6285315 (TTY: switch
tty_buffer_request_room to tty_port)
introduced a potential NULL dereference to some drivers. In
particular, when the device is used as a console, incoming bytes can
kill the box. This is caused by removed checks for TTY against NULL.
It happened because it was unclear to me why the checks were there. I
assumed them superfluous because the interrupts were unbound or
otherwise stopped. But this is not the case for consoles for these
drivers, as was pointed out by David Miller.
Now, this patch re-introduces the checks (at this point we check
port->state, not the tty proper, as we do not care about tty pointers
anymore). For both of the drivers, we place the check below the
handling of break signal so that sysrq can actually work. (One needs
to issue a break and then sysrq key within the following 5 seconds.)
We do not change sc26xx, sunhv, and sunsu here because they behave the
same as before. People having that hardware should fix the driver
eventually, however. They always could unconditionally dereference tty
in receive_chars, port->state in uart_handle_dcd_change, and
up->port.state->port.tty.
There is perhaps more to fix in all those drivers, but they are at
least in a state they were before.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ifx6x60 driver implements both legacy suspend/resume callbacks and
dev_pm_ops. The SPI core is going to ignore legacy suspend/resume
callbacks if a driver implements dev_pm_ops. Since the legacy suspend/resume
callbacks are empty in this case it is safe to just remove them.
Cc: Bi Chao <chao.bi@intel.com>
Cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
mrst_max3110 driver.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
max310x driver.
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
max3100 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as flags, convert to using open/close counts from tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as flags, convert to using *_wait queues from tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as flags, convert to using close delays from tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Well, all those are unused. They were perhaps copied from generic
serial structure ages ago. Remove them for good.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is not used anywhere, so no need to return anything.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, remove STD_FLAGS as the value, or its subvalues
(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) is not tested anywhere --
there is no point to initialize flags to that. Second, use flags
member from tty_port when we have it now. So that we do not waste
space.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->hw_stopped is set only by drivers to remember HW state. If it is
never set to 1 in a particular driver, there is no need to check it in
the driver at all. Remove such checks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no (and never were any) kgdb fields in uart_ops. Setting
them produces a build error:
drivers/tty/serial/bfin_uart.c:1054:2: error: unknown field 'kgdboc_port_startup' specified in initializer
drivers/tty/serial/bfin_uart.c:1054:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/bfin_uart.c:1054:2: warning: (near initialization for 'bfin_serial_pops.ioctl') [enabled by default]
drivers/tty/serial/bfin_uart.c:1055:2: error: unknown field 'kgdboc_port_shutdown' specified in initializer
drivers/tty/serial/bfin_uart.c:1055:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/bfin_uart.c:1055:2: warning: (near initialization for 'bfin_serial_pops.poll_init') [enabled by default]
Remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not dig struct smd_tty_info out of tty_struct using
tty_port_tty_get. It is unnecessarily too complicated, use simple
container_of instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
data_len in jsm_input cannot be zero as we would jump out early in the
function. It also cannot be negative because it is an int and we do
bitwise and with 8192. So remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement console poll for pch_uart, this could enable KGDBoC when
on pch-uart console.
Signed-off-by: Liang Li <liang.li@windriver.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
