commit 097b9146c0e26aabaa6ff3e5ea536a53f5254a79 upstream.
Avoid the assumption that ksize(kmalloc(S)) == ksize(kmalloc(S)): when
cloning an skb, save and restore truesize after pskb_expand_head(). This
can occur if the allocator decides to service an allocation of the same
size differently (e.g. use a different size class, or pass the
allocation on to KFENCE).
Because truesize is used for bookkeeping (such as sk_wmem_queued), a
modified truesize of a cloned skb may result in corrupt bookkeeping and
relevant warnings (such as in sk_stream_kill_queues()).
Link: https://lkml.kernel.org/r/X9JR/J6dMMOy1obu@elver.google.com
Reported-by: syzbot+7b99aafdcc2eedea6178@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210201160420.2826895-1-elver@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee576c47db60432c37e54b1e2b43a8ca6d3a8dca upstream.
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2cac ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7a21b6fbd945f8d8f61422ccd27203c1fafeb7 upstream.
If IPv6 is builtin, we do not need an expensive indirect call
to reach icmp6_send().
v2: put inline keyword before the type to avoid sparse warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b41713b606694257b90d61ba7e2712d8457648b upstream.
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6194f7e6473be78acdc5d03edd116944bdbb2c4e ]
The multiplication of the u32 variables tx_time and estimated_retx is
performed using a 32 bit multiplication and the result is stored in
a u64 result. This has a potential u32 overflow issue, so avoid this
by casting tx_time to a u64 to force a 64 bit multiply.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 050ac52cbe1f ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210205175352.208841-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a758c861ff290e39d4f1ee0aa5df0f0b9a45ee ]
Jump to the label done to decrement the reference count of HCI device
hdev on path that the Inquiry procedure is interrupted.
Fixes: 3e13fa1e1fab ("Bluetooth: Fix hci_inquiry ioctl usage")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5687c644015a097304a2e47476c0ecab2065734 ]
Looks like this was missed when patching the source to clear the structures
throughout, causing this one instance to clear the struct after the response
id is assigned.
Fixes: eddb7732119d ("Bluetooth: A2MP: Fix not initializing all members")
Signed-off-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1c5fae9c9a092574398a17facc31c533791ef232 upstream.
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7536bc7398e2ae552d2fabb7e0e371a9f1fe46 upstream.
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc78367d ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d0bc44d39bca615b72637e340317b7899b7f911 upstream.
A possible locking issue in vsock_connect_timeout() was recognized by
Eric Dumazet which might cause a null pointer dereference in
vsock_transport_cancel_pkt(). This patch assures that
vsock_transport_cancel_pkt() will be called within the lock, so a race
condition won't occur which could result in vsk->transport to be set to NULL.
Fixes: 380feae0def7 ("vsock: cancel packets when failing to connect")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-f8e0937a-cf0e-4d80-a76e-d9a958ba3ef1-1612535522360@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07998281c268592963e1cd623fe6ab0270b65ae4 ]
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes: 4e35c1cb9460240 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1bdde33b72366da20d10770ab7a49fe87b5e190 ]
When both --reap and --update flag are specified, there's a code
path at which the entry to be updated is reaped beforehand,
which then leads to kernel crash. Reap only entries which won't be
updated.
Fixes kernel bugzilla #207773.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207773
Reported-by: Reindl Harald <h.reindl@thelounge.net>
Fixes: 0079c5aee348 ("netfilter: xt_recent: add an entry reaper")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba6dfce47c4d002d96cd02a304132fca76981172 ]
Remove duplicated helper functions to parse opaque XDR objects
and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h.
In the new file carry the license and copyright from the source file
net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside
include/linux/sunrpc/xdr.h since lockd is not the only user of
struct xdr_netobj.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afbc293add6466f8f3f0c3d944d85f53709c170f ]
xfrm_probe_algs() probes kernel crypto modules and changes the
availability of struct xfrm_algo_desc. But there is a small window
where ealg->available and aalg->available get changed between
count_ah_combs()/count_esp_combs() and dump_ah_combs()/dump_esp_combs(),
in this case we may allocate a smaller skb but later put a larger
amount of data and trigger the panic in skb_put().
Fix this by relaxing the checks when counting the size, that is,
skipping the test of ->available. We may waste some memory for a few
of sizeof(struct sadb_comb), but it is still much better than a panic.
Reported-by: syzbot+b2bf2652983d23734c5c@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 18fe0fae61252b5ae6e26553e2676b5fac555951 upstream.
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210201083324.3134-1-nbd@nbd.name
[use rcu_access_pointer() instead since we won't dereference here]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 5018c59607a511cdee743b629c76206d9c9e6d7b ]
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5e0 ("ipv4: call dst_dev_put() properly")
Signed-off-by: Wei Wang <weiwan@google.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88c7a9fd9bdd3e453f04018920964c6f848a591a ]
When sending a packet, we will prepend it with an LAPB header.
This modifies the shared parts of a cloned skb, so we should copy the
skb rather than just clone it, before we prepend the header.
In "Documentation/networking/driver.rst" (the 2nd point), it states
that drivers shouldn't modify the shared parts of a cloned skb when
transmitting.
The "dev_queue_xmit_nit" function in "net/core/dev.c", which is called
when an skb is being sent, clones the skb and sents the clone to
AF_PACKET sockets. Because the LAPB drivers first remove a 1-byte
pseudo-header before handing over the skb to us, if we don't copy the
skb before prepending the LAPB header, the first byte of the packets
received on AF_PACKET sockets can be corrupted.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20210201055706.415842-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 622d3b4e39381262da7b18ca1ed1311df227de86 ]
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 62d9f1a6945ba69c125e548e72a36d203b30596e upstream.
Upon receiving a cumulative ACK that changes the congestion state from
Disorder to Open, the TLP timer is not set. If the sender is app-limited,
it can only wait for the RTO timer to expire and retransmit.
The reason for this is that the TLP timer is set before the congestion
state changes in tcp_ack(), so we delay the time point of calling
tcp_set_xmit_timer() until after tcp_fastretrans_alert() returns and
remove the FLAG_SET_XMIT_TIMER from ack_flag when the RACK reorder timer
is set.
This commit has two additional benefits:
1) Make sure to reset RTO according to RFC6298 when receiving ACK, to
avoid spurious RTO caused by RTO timer early expires.
2) Reduce the xmit timer reschedule once per ACK when the RACK reorder
timer is set.
Fixes: df92c8394e6e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Link: https://lore.kernel.org/netdev/1611311242-6675-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1611464834-23030-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f923c3ab96dbbb4e3c22d1afc1dc1d3b195cd8 upstream.
Put the device to avoid resource leak on path that the polling flag is
invalid.
Fixes: a831b9132065 ("NFC: Do not return EBUSY when stopping a poll that's already stopped")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121153745.122184-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a30537cee233fb7da302491b28c832247d89bbe upstream.
Goto to the label put_dev instead of the label error to fix potential
resource leak on path that the target index is invalid.
Fixes: c4fbb6515a4d ("NFC: The core part should generate the target index")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121152748.98409-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 054c9939b4800a91475d8d89905827bf9e1ad97a ]
syzbot reported a crash that happened when changing the interface
type around a lot, and while it might have been easy to fix just
the symptom there, a little deeper investigation found that really
the reason is that we allowed packets to be transmitted while in
the middle of changing the interface type.
Disallow TX by stopping the queues while changing the type.
Fixes: 34d4bc4d41d2 ("mac80211: support runtime interface type changes")
Reported-by: syzbot+d7a3b15976bf7de2238a@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210122171115.b321f98f4d4f.I6997841933c17b093535c31d29355be3c0c39628@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56ce7c25ae1525d83cf80a880cf506ead1914250 ]
When setting xfrm replay_window to values higher than 32, a rare
page-fault occurs in xfrm_replay_advance_bmp:
BUG: unable to handle page fault for address: ffff8af350ad7920
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD ad001067 P4D ad001067 PUD 0
Oops: 0002 [#1] SMP PTI
CPU: 3 PID: 30 Comm: ksoftirqd/3 Kdump: loaded Not tainted 5.4.52-050452-generic #202007160732
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
RIP: 0010:xfrm_replay_advance_bmp+0xbb/0x130
RSP: 0018:ffffa1304013ba40 EFLAGS: 00010206
RAX: 000000000000010d RBX: 0000000000000002 RCX: 00000000ffffff4b
RDX: 0000000000000018 RSI: 00000000004c234c RDI: 00000000ffb3dbff
RBP: ffffa1304013ba50 R08: ffff8af330ad7920 R09: 0000000007fffffa
R10: 0000000000000800 R11: 0000000000000010 R12: ffff8af29d6258c0
R13: ffff8af28b95c700 R14: 0000000000000000 R15: ffff8af29d6258fc
FS: 0000000000000000(0000) GS:ffff8af339ac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff8af350ad7920 CR3: 0000000015ee4000 CR4: 00000000001406e0
Call Trace:
xfrm_input+0x4e5/0xa10
xfrm4_rcv_encap+0xb5/0xe0
xfrm4_udp_encap_rcv+0x140/0x1c0
Analysis revealed offending code is when accessing:
replay_esn->bmp[nr] |= (1U << bitnr);
with 'nr' being 0x07fffffa.
This happened in an SMP system when reordering of packets was present;
A packet arrived with a "too old" sequence number (outside the window,
i.e 'diff > replay_window'), and therefore the following calculation:
bitnr = replay_esn->replay_window - (diff - pos);
yields a negative result, but since bitnr is u32 we get a large unsigned
quantity (in crash dump above: 0xffffff4b seen in ecx).
This was supposed to be protected by xfrm_input()'s former call to:
if (x->repl->check(x, skb, seq)) {
However, the state's spinlock x->lock is *released* after '->check()'
is performed, and gets re-acquired before '->advance()' - which gives a
chance for a different core to update the xfrm state, e.g. by advancing
'replay_esn->seq' when it encounters more packets - leading to a
'diff > replay_window' situation when original core continues to
xfrm_replay_advance_bmp().
An attempt to fix this issue was suggested in commit bcf66bf54aab
("xfrm: Perform a replay check after return from async codepaths"),
by calling 'x->repl->recheck()' after lock is re-acquired, but fix
applied only to asyncronous crypto algorithms.
Augment the fix, by *always* calling 'recheck()' - irrespective if we're
using async crypto.
Fixes: 0ebea8ef3559 ("[IPSEC]: Move state lock into x->type->input")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c5b7a501e7400869ee905b4f7af3d6717802bcb upstream.
Otherwise, the newly create element shows no timeout when listing the
ruleset. If the set definition does not specify a default timeout, then
the set element only shows the expiration time, but not the timeout.
This is a problem when restoring a stateful ruleset listing since it
skips the timeout policy entirely.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5122565188bae59d507d90a9a9fd2fd6107f4439 upstream.
Since cfg80211 doesn't implement commit, we never really cared about
that code there (and it's configured out w/o CONFIG_WIRELESS_EXT).
After all, since it has no commit, it shouldn't return -EIWCOMMIT to
indicate commit is needed.
However, EIWCOMMIT is actually an alias for EINPROGRESS, which _can_
happen if e.g. we try to change the frequency but we're already in
the process of connecting to some network, and drivers could return
that value (or even cfg80211 itself might).
This then causes us to crash because dev->wireless_handlers is NULL
but we try to check dev->wireless_handlers->standard[0].
Fix this by also checking dev->wireless_handlers. Also simplify the
code a little bit.
Cc: stable@vger.kernel.org
Reported-by: syzbot+444248c79e117bc99f46@syzkaller.appspotmail.com
Reported-by: syzbot+8b2a88a09653d4084179@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210121171621.2076e4a37d5a.I5d9c72220fe7bb133fb718751da0180a57ecba4e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303a40d52439aa141035fca5654ccaccd upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008c25240914984208b2ced57d1dd25a5 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db796 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d687dbdd0f748c5e1df89c977b6c02a upstream.
Commit 3226b158e67c ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e18f ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fbb11ae93c468dfecab169aca9c27b43 upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3feb ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b210de4f8c97d57de051e805686248ec4c6cfc52 ]
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054a4 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d52e419ac8b50c8bef41b398ed13528e75d7ad48 ]
Clang static analysis reports the following:
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca7d ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()")
Reported-by: Tom Rix <trix@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3226b158e67cfaa677fd180152bfb28989cb2fac ]
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd363 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47e4bb147a96f1c9b4e7691e7e994e53838bfff8 ]
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit c269a24ce057 ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com
Fixes: e2f1f072db8d ("sit: allow to configure 6rd tunnels via netlink")
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df85bc140a4d6cbaa78d8e9c35154e1a2f0622c7 ]
In commit 826f328e2b7e ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Fixes: 826f328e2b7e ("net: dcb: Validate netlink message in DCB handler")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 826f328e2b7e8854dd42ea44e6519cd75018e7b1 ]
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
Fixes: 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Signed-off-by: Petr Machata <me@pmachata.org>
Link: https://lore.kernel.org/r/a2a9b88418f3a58ef211b718f2970128ef9e3793.1608673640.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bd6b629c39e3fa9e14243a6d8820492be1a5b2e ]
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a27 ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6351c3f1c27c80535d76cac2299aec44c36291e upstream.
The old way of changing the conntrack hashsize runtime was through changing
the module param via file /sys/module/nf_conntrack/parameters/hashsize. This
was extended to sysctl change in commit 3183ab8997a4 ("netfilter: conntrack:
allow increasing bucket size via sysctl too").
The commit introduced second "user" variable nf_conntrack_htable_size_user
which shadow actual variable nf_conntrack_htable_size. When hashsize is
changed via module param this "user" variable isn't updated. This results in
sysctl net/netfilter/nf_conntrack_buckets shows the wrong value when users
update via the old way.
This patch fix the issue by always updating "user" variable when reading the
proc file. This will take care of changes to the actual variable without
sysctl need to be aware.
Fixes: 3183ab8997a4 ("netfilter: conntrack: allow increasing bucket size via sysctl too")
Reported-by: Yoel Caspersen <yoel@kviknet.dk>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86b53fbf08f48d353a86a06aef537e78e82ba721 upstream.
A return value of 0 means success. This is documented in lib/kstrtox.c.
This was found by trying to mount an NFS share from a link-local IPv6
address with the interface specified by its index:
mount("[fe80::1%1]:/srv/nfs", "/mnt", "nfs", 0, "nolock,addr=fe80::1%1")
Before this commit this failed with EINVAL and also caused the following
message in dmesg:
[...] NFS: bad IP address specified: addr=fe80::1%1
The syscall using the same address based on the interface name instead
of its index succeeds.
Credits for this patch go to my colleague Christian Speich, who traced
the origin of this bug to this line of code.
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Fixes: 00cfaa943ec3 ("replace strict_strto calls")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54970a2fbb673f090b7f02d7f57b10b2e0707155 upstream.
syzbot reproduces BUG_ON in skb_checksum_help():
tun creates (bogus) skb with huge partial-checksummed area and
small ip packet inside. Then ip_rcv trims the skb based on size
of internal ip packet, after that csum offset points beyond of
trimmed skb. Then checksum_tg() called via netfilter hook
triggers BUG_ON:
offset = skb_checksum_start_offset(skb);
BUG_ON(offset >= skb_headlen(skb));
To work around the problem this patch forces pskb_trim_rcsum_slow()
to return -EINVAL in described scenario. It allows its callers to
drop such kind of packets.
Link: https://syzkaller.appspot.com/bug?id=b419a5ca95062664fe1a60b764621eb4526e2cd0
Reported-by: syzbot+7010af67ced6105e5ab6@syzkaller.appspotmail.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1b2494af-2c56-8ee2-7bc0-923fcad1cdf8@virtuozzo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50c661670f6a3908c273503dfa206dfc7aa54c07 ]
For some reason ip_tunnel insist on setting the DF bit anyway when the
inner header has the DF bit set, EVEN if the tunnel was configured with
'nopmtudisc'.
This means that the script added in the previous commit
cannot be made to work by adding the 'nopmtudisc' flag to the
ip tunnel configuration. Doing so breaks connectivity even for the
without-conntrack/netfilter scenario.
When nopmtudisc is set, the tunnel will skip the mtu check, so no
icmp error is sent to client. Then, because inner header has DF set,
the outer header gets added with DF bit set as well.
IP stack then sends an error to itself because the packet exceeds
the device MTU.
Fixes: 23a3647bc4f93 ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb4cc1a18856a73f0ff5137df0c2a31f4c50f6cf ]
Conntrack reassembly records the largest fragment size seen in IPCB.
However, when this gets forwarded/transmitted, fragmentation will only
be forced if one of the fragmented packets had the DF bit set.
In that case, a flag in IPCB will force fragmentation even if the
MTU is large enough.
This should work fine, but this breaks with ip tunnels.
Consider client that sends a UDP datagram of size X to another host.
The client fragments the datagram, so two packets, of size y and z, are
sent. DF bit is not set on any of these packets.
Middlebox netfilter reassembles those packets back to single size-X
packet, before routing decision.
packet-size-vs-mtu checks in ip_forward are irrelevant, because DF bit
isn't set. At output time, ip refragmentation is skipped as well
because x is still smaller than the mtu of the output device.
If ttransmit device is an ip tunnel, the packet size increases to
x+overhead.
Also, tunnel might be configured to force DF bit on outer header.
In this case, packet will be dropped (exceeds MTU) and an ICMP error is
generated back to sender.
But sender already respects the announced MTU, all the packets that
it sent did fit the announced mtu.
Force refragmentation as per original sizes unconditionally so ip tunnel
will encapsulate the fragments instead.
The only other solution I see is to place ip refragmentation in
the ip_tunnel code to handle this case.
Fixes: d6b915e29f4ad ("ip_fragment: don't forward defragmented DF packet")
Reported-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55b7ab1178cbf41f979ff83236d3321ad35ed2ad ]
VLAN checks for NETREG_UNINITIALIZED to distinguish between
registration failure and unregistration in progress.
Since commit cb626bf566eb ("net-sysfs: Fix reference count leak")
registration failure may, however, result in NETREG_UNREGISTERED
as well as NETREG_UNINITIALIZED.
This fix is similer to cebb69754f37 ("rtnetlink: Fix
memory(net_device) leak when ->newlink fails")
Fixes: cb626bf566eb ("net-sysfs: Fix reference count leak")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c8193f568ae16f3242abad6518dc2ca6c8eef86 upstream.
htable_bits() can call jhash_size(32) and trigger shift-out-of-bounds
UBSAN: shift-out-of-bounds in net/netfilter/ipset/ip_set_hash_gen.h:151:6
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 8498 Comm: syz-executor519
Not tainted 5.10.0-rc7-next-20201208-syzkaller #0
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395
htable_bits net/netfilter/ipset/ip_set_hash_gen.h:151 [inline]
hash_mac_create.cold+0x58/0x9b net/netfilter/ipset/ip_set_hash_gen.h:1524
ip_set_create+0x610/0x1380 net/netfilter/ipset/ip_set_core.c:1115
nfnetlink_rcv_msg+0xecc/0x1180 net/netfilter/nfnetlink.c:252
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
nfnetlink_rcv+0x1ac/0x420 net/netfilter/nfnetlink.c:600
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x907/0xe40 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e8/0x810 net/socket.c:2345
___sys_sendmsg+0xf3/0x170 net/socket.c:2399
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2432
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch replaces htable_bits() by simple fls(hashsize - 1) call:
it alone returns valid nbits both for round and non-round hashsizes.
It is normal to set any nbits here because it is validated inside
following htable_size() call which returns 0 for nbits>31.
Fixes: 1feab10d7e6d("netfilter: ipset: Unified hash type generation")
Reported-by: syzbot+d66bfadebca46cf61a2b@syzkaller.appspotmail.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
