This patch adds the sound subsystem driver for Odroid-X2 and
Odroid-U3 boards. The codec works in I2S master mode; there
are two separate audio routing paths defined, as there are
differences in the signal routing between the X2 and U3 boards,
i.e. U3 uses single jack for headphones and microphone.
Signed-off-by: Chen Zhen <zhen1.chen@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replaced snd_soc_register_component with its devres equivalent,
devm_snd_soc_register_component.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replaced snd_soc_register_component with its devres equivalent,
devm_snd_soc_register_component.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using the sgtl5000 codec driver as a module and trying to remove it causes the
followig kernel oops:
root@freescale /$ rmmod snd-soc-imx-sgtl5000
[ 117.122920] ------------[ cut here ]------------
[ 117.127609] WARNING: CPU: 0 PID: 631 at drivers/regulator/core.c:3604 regula)
[ 117.137046] Modules linked in: snd_soc_imx_sgtl5000(-) snd_soc_sgtl5000 evbug
[ 117.144315] CPU: 0 PID: 631 Comm: rmmod Not tainted 3.16.0-rc3-next-201407043
[ 117.153366] Backtrace:
[ 117.155865] [<80011e5c>] (dump_backtrace) from [<80011ff8>] (show_stack+0x18)
[ 117.163484] r6:802fcc48 r5:00000000 r4:00000000 r3:00000000
[ 117.169228] [<80011fe0>] (show_stack) from [<80668cc0>] (dump_stack+0x88/0xa)
[ 117.176508] [<80668c38>] (dump_stack) from [<80029a38>] (warn_slowpath_commo)
[ 117.184696] r5:00000009 r4:00000000
[ 117.188322] [<800299c8>] (warn_slowpath_common) from [<80029a80>] (warn_slow)
[ 117.197150] r8:dd60d600 r7:ddfa6d00 r6:dd5d9064 r5:dd5e0f90 r4:dd5d9400
[ 117.203983] [<80029a5c>] (warn_slowpath_null) from [<802fcc48>] (regulator_u)
[ 117.212828] [<802fcb74>] (regulator_unregister) from [<7f0047c4>] (ldo_regul)
[ 117.223475] r4:dd59e300 r3:dd5e0f90
[ 117.227100] [<7f00479c>] (ldo_regulator_remove [snd_soc_sgtl5000]) from [<7f)
[ 117.238959] r4:dd5d8000 r3:ddd51420
[ 117.242623] [<7f0047dc>] (sgtl5000_remove [snd_soc_sgtl5000]) from [<804e5b1)
[ 117.252489] r5:00000000 r4:dd5d8000
[ 117.256111] [<804e5af8>] (soc_remove_codec) from [<804e5ed4>] (soc_remove_da)
[ 117.264933] r4:ddfb640c r3:00000000
[ 117.268555] [<804e5c10>] (soc_remove_dai_links) from [<804e5fbc>] (snd_soc_u)
[ 117.277810] r10:80359e48 r9:dd684000 r8:dd5ca800 r7:dd685e60 r6:00000001 r5c
[ 117.285761] r4:dd5d9064
[ 117.288329] [<804e5f28>] (snd_soc_unregister_card) from [<804f29f0>] (devm_c)
[ 117.297324] r6:00000004 r5:ddd0fc10 r4:dd5a7980 r3:804f29dc
[ 117.303095] [<804f29dc>] (devm_card_release) from [<8035a418>] (release_node)
[ 117.311369] [<8035a2a8>] (release_nodes) from [<8035aab4>] (devres_release_a)
[ 117.319583] r10:00000000 r9:dd684000 r8:8000ed64 r7:00000081 r6:ddd0fc44 r54
[ 117.327543] r4:ddd0fc10
[ 117.330108] [<8035aa7c>] (devres_release_all) from [<803571c8>] (__device_re)
[ 117.339214] r4:ddd0fc10 r3:dd5d9010
[ 117.342989] [<80357148>] (__device_release_driver) from [<80357a48>] (driver)
[ 117.351607] r5:7f00c9e4 r4:ddd0fc10
[ 117.355285] [<8035798c>] (driver_detach) from [<80357030>] (bus_remove_drive)
[ 117.363454] r6:00000880 r5:00000000 r4:7f00c9e4 r3:dd6c3a80
[ 117.369195] [<80356fdc>] (bus_remove_driver) from [<803580b8>] (driver_unreg)
[ 117.377683] r4:7f00c9e4 r3:dd60d480
[ 117.381305] [<80358088>] (driver_unregister) from [<80358bb4>] (platform_dri)
[ 117.390642] r4:7f00ca28 r3:7f00c35c
[ 117.394309] [<80358ba0>] (platform_driver_unregister) from [<7f00c370>] (imx)
[ 117.406188] [<7f00c35c>] (imx_sgtl5000_driver_exit [snd_soc_imx_sgtl5000]) f)
[ 117.417452] [<8008c2b8>] (SyS_delete_module) from [<8000eba0>] (ret_fast_sys)
[ 117.425753] r6:5f636f73 r5:5f646e73 r4:00016f40
[ 117.430428] ---[ end trace 8fd8a5cb39e46d0e ]---
This problem is well explained by Russell King:
"The sgtl5000 uses a two-stage initialisation process. The first stage
is when the platform driver is probed, where some resources are found
and initialised. The second stage is via the codec driver's probe
function, where regulators are found and initialised using the managed
resource support.
The problem here is that this works fine until the codec driver is
unbound. When this occurs, sgtl5000_remove() is called which is a no-op
as far as the managed resource code is concerned. The regulators remain
allocated, and their pointers in sgtl5000_priv remain valid.
If the codec is now re-probed, it will again try and find the regulators,
which will now be busy. This will fail.
That's not the only problem - if using the LDO regulator, the regulator
is unregistered from the regulator core code, but it still has a user.
When the user is cleaned up (eg, by removing the module) it hits the
free'd regulator, and this can oops the kernel.
This bug was originally introduced by 63e54cd9caa3ce ("ASoC: sgtl5000:
Use devm_regulator_bulk_get()")."
This reverts commit 63e54cd9caa3ce.
Tested on a imx53-qsb board.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_of_parse_card_name() may be called before card->dev has been
set, which results in a kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 00000210
PC is at snd_soc_of_parse_card_name+0x18/0x54
LR is at snow_probe+0x5c/0xd4
Add an error check in snd_soc_of_parse_card_name() to take care of this
case and print out a message in case of error.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver for i2s controller found on rk3066, rk3168 and rk3288
processors from rockchip.
Tested on the RK3288 SDK board.
Signed-off-by: Jianqun Xu <xjq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Swap controls for ADC/PCM paths should be in the DAPM domain.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now the led_power_filter() needs to handle 3 situations:
- only mute_led_nid is set
- only cap_mute_led_nid is set
- both mute_led_ind and cap_mute_led_nid are set
BugLink: https://bugs.launchpad.net/bugs/1329580
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0070 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The max98090_{suspend,resume}() functions are used for system sleep and
therefore need to be guarded by CONFIG_PM_SLEEP rather than CONFIG_PM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fix the issue that the output is almost silent at the
beginning of starting a playback.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The hda_tegra_disable_clocks() function is only used by the suspend and
resume code, so it needs to be included in the #ifdef CONFIG_PM_SLEEP
block to prevent the following warning:
CC sound/pci/hda/hda_tegra.o
sound/pci/hda/hda_tegra.c:238:13: warning: 'hda_tegra_disable_clocks' defined but not used [-Wunused-function]
static void hda_tegra_disable_clocks(struct hda_tegra *data)
^
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move codec initial settings from asoc probe to i2c probe.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch modifies the voltage level in the BIAS OFF stage
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch removes the redundant definition in head file
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
print_nid_path has a possible buffer overflow if
struct nid_path.path values are > 256.
Avoid this and neaten the output to remove the leading ':'
Neaten debug_badness to always verify arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The s6105-ipcam driver calls i2c_register_board_info() which means that
not only does it need I2C to be enabled to be built but since that
symbol is not exported it means that the driver also can't be linked as
a module. Use a bool instead of a tristate and add a dependency on I2C
to fix these issues.
Commit b5dd60fd263 (ASoC: s6000: Allow to build when COMPILE_TEST is
enabled) made this problem more visible since it enabled build of the
driver on more common architectures but this has always been an issue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Snow sound-card driver supports multiple boards with different
audio codecs. Updating the sound card name per board basis would provide
some more information to the end-user.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
max98090_handle_pdata() is not doing anything other than printing
a message if pdata is not valid. This can be removed.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CODEC type (MAX98090/MAX98091) can be specified from device-tree file,
it can also be obtained from the CODEC during runtime.
Add an explicit check to figure out if both are matching, else print
a message warning about the same.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We should save/restore relevant I2S registers regardless of
the dai->active flag, otherwise some settings are being lost
after system suspend/resume cycle. E.g. I2S slave mode set only
during dai initialization is not preserved and the device ends
up in master mode after system resume.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The newly introduced sirf-usp driver defines sirf_usp_pcm_{suspend,resume}
functions only when PM_RUNTIME is enabled, but also uses them when that
is disabled and only PM_SLEEP is turned on, resulting in this error:
../sound/soc/sirf/sirf-usp.c: In function 'sirf_usp_pcm_suspend':
../sound/soc/sirf/sirf-usp.c:308:3: error: implicit declaration of function 'sirf_usp_pcm_runtime_suspend' [-Werror=implicit-function-declaration]
sirf_usp_pcm_runtime_suspend(dev);
^
../sound/soc/sirf/sirf-usp.c: In function 'sirf_usp_pcm_resume':
../sound/soc/sirf/sirf-usp.c:319:3: error: implicit declaration of function 'sirf_usp_pcm_runtime_resume' [-Werror=implicit-function-declaration]
ret = sirf_usp_pcm_runtime_resume(dev);
^
cc1: some warnings being treated as errors
To fix that, this patch changes the #ifdef to CONFIG_PM, which
is enabled when at least one of PM_SLEEP or PM_RUNTIME are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
All CODEC input and output widgets are either in the DAPM routing table or
manually marked as non-connected. This means the card is fully routed and we can
let the core take care of disconnecting non-connected pins.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Most of the ASoC s6000 code is architecture independent. This patch makes it
possible to select the platform when COMPILE_TEST is enabled.
The only architecture dependent code is the PCM driver which will still only be
selected if XTENSA_VARIANT_S6000 is enabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The platform_driver remove callback return type is int not void.
Fixes the following warning:
sound/soc/s6000/s6000-i2s.c:604:19: warning: incorrect type in initializer (different base types)
sound/soc/s6000/s6000-i2s.c:604:19: expected int ( *remove )( ... )
sound/soc/s6000/s6000-i2s.c:604:19: got void ( static [toplevel] *<noident>)( ... )
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case of _3LE/_3BE formats the samples are stored in 3 consecutive bytes
without padding it to 4 bytes. This means that the DMA needs to be able to
support 3 bytes word length in order to read/write the samples from memory
correctly. Originally the code treated 24 bits physical length samples as
they were 32 bits which leads to corruption when playing or recording audio.
The hw.formats field has already been prepared to exclude formats not
supported by the DMA engine in use, which means that only on platforms where
3 bytes is supported by the DMA will be able to use this format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Based on the dma_slave_caps's addr_widths queried from the dma driver
prepare the hw.formats mask to include only formats which is supported by
the DMA engine.
In case the dma driver does not implement the slave_caps the default
assumption is that it supports 1, 2 and 4 bytes widths.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
params_physical_width() is available via pcm_params.h
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Realtek ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode.
It is controlled by HD-A verb commands via I2C protocol.
The following is the I/O difference between ALC286 and general I2S codecs.
1. A HD-A verb command contains three parts, NID, VID, and PID.
And an I2S command contains only two parts: address and data.
2. Not only the register address is written, but the read command also
includes the entire write command.
3. rt286 uses different registers for read and write the same bits.
We map verb command to regmap structure. However, we read most registers from
cache to prevent the asymmetry read/write issue in rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Gustaw Lewandowski <gustaw.lewandowski@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since MODULE_LICENSE is missing the module load fails,
so add this for module.
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This small patch completes #defines for Control/Status Register,
adds comments for the missing ones there and on the Interrupt Mask
Register and additionally corrects "#define ICE1712_SERR_LEVEL 0x04 -> 0x08",
according to documentation.
Signed-off-by: Konstantinos Tsimpoukas <kostaslinuxxx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a long standing bug in the read register routing of adau1701.
The bytes arrive in the buffer in big-endian, so the result has to be
shifted before and-ing the bytes in the loop.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch adds ASoC support for SiRF SoCs USP interface.
Features include:
1. Only support slave mode.
2. Support I2S and DSP_A mode.
3. Support S16_LE, S24_LE and S24_3LE formats.
4. Support stereo and mono mode.
5. The biggest Support is 192Khz sample rate.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two power domains, DVDD and AVDD. Enable them both as
long as the codec is in use.
Also, switch on the power to identify the chip at device probe level,
and switch it off again afterwards. The codec level will take care for
power handling later.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are two call sites for snd_soc_post_component_init(), one passes 0 and the
other 1 for the 'dailess' parameter of snd_soc_post_component_init(). Depending
on whether 'dailess' is 0 or 1 snd_soc_post_component_init() runs different code
at the beginning and the end of the function. The patch moves this conditional
code out of snd_soc_post_component_init() and into the call sites. This removes
the need for snd_soc_post_component_init() to know whether it is called for a
DAI link or a aux dev.
Also do the initialization of rtd->card when the rtd struct is allocated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently in snd_soc_instantiate_card() we only check if the aux dev exists, but
do not yet assign it to its rtd. This means that we need to lookup the aux dev
again in soc_probe_aux_dev(). This patch changes the behavior to assign the aux
dev to the rtd in soc_check_aux_dev() (and renames it to soc_bind_aux_dev()).
This simplifies the implementation a bit and also removes the need for
soc_post_component_init() to know about the specific CODEC that was assigned to
the rtd. The later is necessary for componentization as the code should work for
all types of components not just CODECs. This new behavior is also more in sync
with how soc_bind_dai_link()/soc_probe_link_dais() works.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_find_matching_codec() works in the same way as soc_find_codec() except that
it only works for auxdevs. It can easily be replaced by the generic
soc_find_codec().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
rtd->codec is already initialized in soc_bind_dai_link(), so there is no need to
do it again in soc_dai_link_init(). Removing the rtd->codec initialization from
soc_dai_link_init() also removes the need for soc_dai_link_init() to know about
the CODEC at all.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a minimum support of Realtek ALC5670 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound uses Audio DMAC and Audio DMAC peri peri.
Audio DMAC peri peri transfers data inside circuit.
DMA transfer needs source / destination address,
and destination address can be set via dmaengine_slave_config().
The source address can be set when starting DMAEngine.
Because Audio DMAC peri peri always ignores its value,
current driver always used same source address for
Audio DMAC / Audio DMAC peri peri
(Audio DMAC peri peri source / destination address
is always fixed value)
But, This is not good match for DT booting.
This patch properly uses DMA start address
for Audio DMAC / Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
