This is a very simple bitbanging I2C bus driver utilizing the new
arch-neutral GPIO API. Useful for chips that don't have a built-in
I2C controller, additional I2C busses, or testing purposes.
To use, include something similar to the following in the
board-specific setup code:
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PIN_FOO,
.scl_pin = GPIO_PIN_BAR,
};
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
Register this platform_device, set up the I2C pins as GPIO if
required and you're ready to go. This will use default values for
udelay and timeout, and will work with GPIO hardware that does not
support open drain mode, but allows sensing of the SDA and SCL lines
even when they are being driven.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the i2c_smbus_read_block_data helper function, it is needed
by the upcoming lm93 hardware monitoring driver and possibly others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The original i2c-algo-bit implementation uses a 33/66 SCL duty cycle
when bits are being written on the bus. While the I2C specification
doesn't forbid it, this prevents us from driving the I2C bus to its
max speed, limiting us to 66 kbps max on standard I2C busses.
Implementing a 50/50 duty cycle instead lets us max out the bandwidth
up to the theoretical max of 100 kbps on standard I2C busses. This is
particularly important when large amounts of data need to be transfered
over the bus, as is the case with some TV adapters when the firmware is
being uploaded.
In fact this change even allows, at least in theory, fast-mode I2C
support at 125, 166 and 250 kbps. There's no way to reach the
theoretical max of 400 kbps with this implementation. But I don't
think we want to put efforts in that direction anyway: software-driven
I2C is very CPU-intensive and bad for latency.
Other timing changes:
* Don't set SDA high explicitly on error, we're going to issue a stop
condition before we leave anyway.
* If an error occurs when sending the slave address, yield the CPU
before retrying, and remove the additional delay after the new start
condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c linux driver for blackfin architecture which supports blackfin
on-chip TWI controller i2c operation.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make i2c_del_driver a void function, like all other driver removal
functions. It always returned 0 even when errors occured, and nobody
ever actually checked the return value anyway. And we cannot fail
a module removal anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the declaration of i2c-isa-only exported symbols to i2c-isa
itself, that's the best way to ensure nobody will attempt to use them.
Hopefully we'll get rid of the exports themselves soon anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a new helper function to instantiate an i2c device. It is meant as a
replacement for i2c_new_device() when you don't know for sure at which
address your I2C/SMBus device lives. This happens frequently on TV
adapters for example, you know there is a tuner chip on the bus, but
depending on the exact board model and revision, it can live at different
addresses. So, the new i2c_new_probed_device() function will probe the bus
according to a list of addresses, and as soon as one of these addresses
responds, it will call i2c_new_device() on that one address.
This function will make it possible to port the old i2c drivers to the
new model quickly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add i2c_bit_add_numbered_bus(), which is equivalent to i2c_bit_add_bus
except that it calls i2c_add_numbered_adapter() at the end instead of
i2c_add_adapter().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds a call, i2c_add_numbered_adapter(), registering an I2C adapter
with a specific bus number and then creating I2C device nodes for any
pre-declared devices on that bus. It builds on previous patches adding
I2C probe() and remove() support, and that pre-declaration of devices.
This completes the core support for "new style" I2C device drivers.
Those follow the standard driver model for binding devices to drivers
(using probe and remove methods) rather than a legacy model (where the
driver tries to autoconfigure each bus, and registers devices itself).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More update for new style driver support: add a remove() method, and
use it in the relevant code paths.
Again, nothing will use this yet since there's nothing to create devices
feeding this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
One of a series of I2C infrastructure updates to support enumeration using
the standard Linux driver model.
This patch updates probe() and associated hotplug/coldplug support, but
not remove(). Nothing yet _uses_ it to create I2C devices, so those
hotplug/coldplug mechanisms will be the only externally visible change.
This patch will be an overall NOP since the I2C stack doesn't yet create
clients/devices except as part of binding them to legacy drivers.
Some code is moved earlier in the source code, helping group more of the
per-device infrastructure in one place and simplifying handling per-device
attributes.
Terminology being adopted: "legacy drivers" create devices (i2c_client)
themselves, while "new style" ones follow the driver model (the i2c_client
is handed to the probe routine). It's an either/or thing; the two models
don't mix, and drivers that try mixing them won't even be registered.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the I2C bus drivers emulate the SMBus Block Read and Block Process
Call transactions if they wish. This requires to define a new message
flag, which i2c-core will use to let the underlying I2C bus driver
know that the first received byte will specify the length of the read
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename dev_to_i2c_adapter() as to_i2c_adapter(), since the previous
syntax was a surprising and needless difference from normal naming
conventions in Linux.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This shrinks the size of "struct i2c_client" by 40 bytes:
- Substantially shrinks the string used to identify the chip type
- The "flags" don't need to be so big
- Removes some internal padding
It also adds kerneldoc for that struct, explaining how "name" is really a
chip type identifier; it's otherwise potentially confusing.
Because the I2C_NAME_SIZE symbol was abused for both i2c_client.name
and for i2c_adapter.name, this needed to affect i2c_adapter too. The
adapters which used that symbol now use the more-obviously-correct
idiom of taking the size of that field.
JD: Shorten i2c_adapter.name from 50 to 48 bytes while we're here, to
avoid wasting space in padding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter_driver as it doesn't make sense and it prevents
further i2c-core cleanups. i2c_adapter devices are virtual devices
(ex-class devices) and as such they don't need a driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter.class_dev. Instead, set the class of i2c_adapter.dev
to i2c_adapter_class, so that a symlink will be created for every
i2c_adapter in /sys/class/i2c-adapter.
The same change must be mirrored to i2c-isa as it duplicates some
of the i2c-core functionalities.
User-space tools and libraries might need some adjustments. In
particular, libsensors from lm_sensors 2.10.3 or later is required for
proper discovery of i2c adapter names after this change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix handling of low voltage MMC cards.
The latest MMC and SD specs both agree that support for
low-voltage operations is indicated by bit 7 in the OCR.
The MMC spec states that the low voltage range is
1.65-1.95V while the SD spec leaves the actual voltage
range undefined - meaning that there is still no such
thing as a low voltage SD card.
However, an old Sandisk spec implied that bits 7.0
represented voltages below 2.0V in 1V or 0.5V increments,
and the code was accordingly written with that expectation.
This confusion meant that host drivers attempting to support
the typical low voltage (1.8V) would set the wrong bits in
the host OCR mask (usually bits 5 and/or 6) resulting in the
the low voltage mode never being used.
This change corrects the low voltage range and adds sanity
checks on the reserved bits (0-6) and for SD cards that
claim to support low-voltage operations.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Consolidate the list of available voltages.
Up until now, a separate set of defines has been
used for host->vdd than that used for the OCR
voltage mask values. Having two sets of defines
allows them to get out of sync and the current
sets are already inconsistent with one claiming
to describe ranges and the other specific voltages.
Only the SDHCI driver uses the host->vdd defines and
it is easily fixed to use the OCR defines.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Delegate protocol handling to "bus handlers". This allows the core to
just handle the task of arbitrating the bus. Initialisation and
pampering of cards is now done by the different bus handlers.
This design also allows MMC and SD (and later SDIO) to be more cleanly
separated, allowing easier maintenance.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we kill of any pending detection runs when the host
is removed instead of when it is freed. Also add some debugging
to make sure the driver doesn't queue up more detection after it
has removed the host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
All host drivers were #include:ing mmc/protocol.h just to
get access to the OCR bit defines. Move these to host.h instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for MMC 4.2 sector based cards. This tweaks the init a
bit and reads a new field out of the EXT_CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It was found that delays associated with issue and completion of the commands
severely limit performance of the new, fast SD cards. To alleviate this issue
scatter-gather emulation in software is implemented for both dma and pio
transfer modes. Non-block aligned and high memory sg entries are accounted
for.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
State machine used to to track mmc command state was found to be fragile
and unreliable, making many cards unusable. The safer solution is to perform
all needed checks at every card event.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the device management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the adapter management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Freezeable workqueue makes sure that adapter work items (device insertions
and removals) would be handled after the system is fully resumed. Previously
this was achieved by explicit freezing of the kthread.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code duplicating the kernel functionality and clean up data
structures involved in driver matching.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of passing transformed value of adapter interrupt status to
socket drivers, implement two separate callbacks - one for card events
and another for dma events.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add code to accept purge commands from userland.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
READDIRPLUS can be a performance hindrance when the client is working with
large directories. In addition, some servers still have bugs in their
implementations (e.g. Tru64 returns wrong values for the fsid).
Add a mount flag to enable users to turn it off at mount time following the
implementation in Apple's NFS client.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
net/sunrpc/pmap_clnt.c has been replaced by net/sunrpc/rpcb_clnt.c.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a replacement for the in-kernel portmapper client that supports
all 3 versions of the rpcbind protocol. This code is not used yet.
Original code by Groupe Bull updated for the latest kernel, with multiple
bug fixes.
Note that rpcb_clnt.c does not yet support registering via versions 3 and
4 of the rpcbind protocol. That is planned for a later patch.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently rpc_malloc sets req->rq_buffer internally. Make this a more
generic interface: return a pointer to the new buffer (or NULL) and
make the caller set req->rq_buffer and req->rq_bufsize. This looks much
more like kmalloc and eliminates the side effects.
To fix a potential deadlock, this patch also replaces GFP_NOFS with
GFP_NOWAIT in rpc_malloc. This prevents async RPCs from sleeping outside
the RPC's task scheduler while allocating their buffer.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC buffer size estimation logic in net/sunrpc/clnt.c always
significantly overestimates the requirements for the buffer size.
A little instrumentation demonstrated that in fact rpc_malloc was never
allocating the buffer from the mempool, but almost always called kmalloc.
To compute the size of the RPC buffer more precisely, split p_bufsiz into
two fields; one for the argument size, and one for the result size.
Then, compute the sum of the exact call and reply header sizes, and split
the RPC buffer precisely between the two. That should keep almost all RPC
buffers within the 2KiB buffer mempool limit.
And, we can finally be rid of RPC_SLACK_SPACE!
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NLM version 4 requests estimate the call and reply header sizes rather
conservatively, using the very maximum size allowed in the protocol even
though Linux always uses only a small fraction of the allowable space.
Reduce the size of caller and lock arguments to conserve RPC buffer space
while XDR encoding NLM4 arguments. Add compile-time checks to ensure the
hostname string won't overflow NLM protocol maximums.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently we do write coalescing in a very inefficient manner: one pass in
generic_writepages() in order to lock the pages for writing, then one pass
in nfs_flush_mapping() and/or nfs_sync_mapping_wait() in order to gather
the locked pages for coalescing into RPC requests of size "wsize".
In fact, it turns out there is actually a deadlock possible here since we
only start I/O on the second pass. If the user signals the process while
we're in nfs_sync_mapping_wait(), for instance, then we may exit before
starting I/O on all the requests that have been queued up.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Do the coalescing of read requests into block sized requests at start of
I/O as we scan through the pages instead of going through a second pass.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
