commit 0b479790684192ab7024ce6a621f93f6d0a64d92 upstream.
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3ae3401aa19432ee4943eb0bbc2ec704d07d793 upstream.
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9f39a785a9977e72233000711ef1eb48203551 upstream.
In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0741ba40a009f97c019ae7541dc61c1fdf41efb upstream.
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b67 ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cce6f6eeced5ddd9cac55e807fe28b4f18c1ba upstream.
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in sd. If we fail allocating the special page, we return
busy, and it'll get retried. But since ordering is honored for dispatch
requests, we can keep retrying this same IO and failing. Behind that IO
could be requests that want to free memory, but they never get the
chance. This means you get repeated spews of traces like this:
[1201401.625972] Call Trace:
[1201401.631748] dump_stack+0x4d/0x65
[1201401.639445] warn_alloc+0xec/0x190
[1201401.647335] __alloc_pages_slowpath+0xe84/0xf30
[1201401.657722] ? get_page_from_freelist+0x11b/0xb10
[1201401.668475] ? __alloc_pages_slowpath+0x2e/0xf30
[1201401.679054] __alloc_pages_nodemask+0x1f9/0x210
[1201401.689424] alloc_pages_current+0x8c/0x110
[1201401.699025] sd_setup_write_same16_cmnd+0x51/0x150
[1201401.709987] sd_init_command+0x49c/0xb70
[1201401.719029] scsi_setup_cmnd+0x9c/0x160
[1201401.727877] scsi_queue_rq+0x4d9/0x610
[1201401.736535] blk_mq_dispatch_rq_list+0x19a/0x360
[1201401.747113] blk_mq_sched_dispatch_requests+0xff/0x190
[1201401.758844] __blk_mq_run_hw_queue+0x95/0xa0
[1201401.768653] blk_mq_run_work_fn+0x2c/0x30
[1201401.777886] process_one_work+0x14b/0x400
[1201401.787119] worker_thread+0x4b/0x470
[1201401.795586] kthread+0x110/0x150
[1201401.803089] ? rescuer_thread+0x320/0x320
[1201401.812322] ? kthread_park+0x90/0x90
[1201401.820787] ? do_syscall_64+0x53/0x150
[1201401.829635] ret_from_fork+0x29/0x40
Ensure that the discard page allocation has a mempool backing, so we
know we can make progress.
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2419f30a4a4fcaa5f35111563b4c61f1b2b26841 upstream.
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8a5 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45f750c16cae3625014c14c77bd9005eda975d35 upstream.
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5146f95df782b0ac61abde36567e718692725c89 upstream.
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d204ee9d671327915260071c19350d84344e096 upstream
The "le32_to_cpu(rsp->OutputOffset) + *plen" addition can overflow and
wrap around to a smaller value which looks like it would lead to an
information leak.
Fixes: 4a72dafa19ba ("SMB2 FSCTL and IOCTL worker function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2015516c5c0be932a69e1d3405c2fb03b4eacf1 ]
We need to synthesize events first, because some features works on top
of them (on report side).
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180314092205.23291-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 00ee8b60102862f4daf0814d12a2ea2744fc0b9b upstream
We have to account the name of the symlink and not the target length.
Fixes: ca7f85be8d6c ("ubifs: Add support for encrypted symlinks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 747df19747bc9752cd40b9cce761e17a033aa5c2 upstream
The ESD watchdog code in sta32x_watchdog() dereferences the pointer
which is never assigned.
This is a regression from a1be4cead9b950 ("ASoC: sta32x: Convert to direct
regmap API usage.") which went unnoticed since nobody seems to use that ESD
workaround.
Fixes: a1be4cead9b950 ("ASoC: sta32x: Convert to direct regmap API usage.")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b88aef36b87c9787a4db724923ec4f57dfd513f3 ]
If __blkdev_issue_discard is in progress and a device mapper device is
reloaded with a table that doesn't support discard,
q->limits.max_discard_sectors is set to zero. This results in infinite
loop in __blkdev_issue_discard.
This patch checks if max_discard_sectors is zero and aborts with
-EOPNOTSUPP.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Zdenek Kabelac <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af097f5d199e2aa3ab3ef777f0716e487b8f7b08 ]
Don't build discards bigger than what the user asked for, if the
user decided to limit the size by writing to 'discard_max_bytes'.
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
emit_ldx_r() and emit_a32_mov_i() were both using TMP_REG_1 and
clashing with each other. Using TMP_REG_2 in emit_ldx_r() fixes
the issue.
Fixes: ec19e02b343 ("ARM: net: bpf: fix LDX instructions")
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7f3a249dbed2858e6c2f30e5be7f1f7a709ee2 ]
In order to read correctly from asynchronously updated RTC registers,
it's necessary to read repeatedly until their values do not change from
read to read. It's also necessary to wait for three RTC clock ticks for
certain operations. There are no timeouts in this code and these
operations could possibly loop forever.
To avoid kernel hangs, put in timeouts.
The iMX7d can be configured to stop the SRTC on a tamper event, which
will lockup the kernel inside this driver as described above.
These hangs can happen when running under qemu, which doesn't emulate
the SNVS RTC, though currently the driver will refuse to load on qemu
due to a timeout in the driver probe method.
It could also happen if the SRTC block where somehow placed into reset
or the slow speed clock that drives the SRTC counter (but not the CPU)
were to stop.
The symptoms on a two core iMX7d are a work queue hang on
rtc_timer_do_work(), which eventually blocks a systemd fsnotify
operation that triggers a work queue flush, causing systemd to hang and
thus causing all services that should be started by systemd, like a
console getty, to fail to start or stop.
Also optimize the wait code to wait less. It only needs to wait for the
clock to advance three ticks, not to see it change three times.
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dcdf9d4e15189ecfda24cc87339a3425448d5c ]
nvmet_rdma_release_rsp() may free the response before using it at error
flow.
Fixes: 8407879 ("nvmet-rdma: fix possible bogus dereference under heavy load")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ece27a337d42a3197935711997f2880f0957ed7e ]
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8469636ab5d8c77645b953746c10fda6983a8830 ]
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0544ee4b1ad574aec3b6379af5f5cdee42840971 ]
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c7f25cae54b840302e4f1b371dbf318fbf09ab2 ]
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 993107fea5eefdfdfde1ca38d3f01f0bebf76e77 ]
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c38f57da428b033f2721b611d84b1f40bde674a8 ]
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Reported-by: Maximilian Riemensberger <riemensberger@cadami.net>
Cc: Graham Whaley <graham.whaley@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e785302dad32228819d8066e5376acd15d0e6ba ]
Missing a dependency. Shouldn't show cifs posix extensions
in Kconfig if CONFIG_CIFS_ALLOW_INSECURE_DIALECTS (ie SMB1
protocol) is disabled.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e594a5e349ddbfdaca1951bb3f8d72f3f1660d73 ]
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecb239d96d369c23c33d41708646df646de669f4 ]
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e7762 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d0358d0ba048c5afb1385787aaec8fa5ad78fcc ]
Chris has discovered and reported that v7_dma_inv_range() may corrupt
memory if address range is not aligned to cache line size.
Since the whole cache-v7m.S was lifted form cache-v7.S the same
observation applies to v7m_dma_inv_range(). So the fix just mirrors
what has been done for v7 with a little specific of M-class.
Cc: Chris Cole <chris@sageembedded.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1208f6a822ac29933e772ef1f637c5d67838da9 ]
This patch addresses possible memory corruption when
v7_dma_inv_range(start_address, end_address) address parameters are not
aligned to whole cache lines. This function issues "invalidate" cache
management operations to all cache lines from start_address (inclusive)
to end_address (exclusive). When start_address and/or end_address are
not aligned, the start and/or end cache lines are first issued "clean &
invalidate" operation. The assumption is this is done to ensure that any
dirty data addresses outside the address range (but part of the first or
last cache lines) are cleaned/flushed so that data is not lost, which
could happen if just an invalidate is issued.
The problem is that these first/last partial cache lines are issued
"clean & invalidate" and then "invalidate". This second "invalidate" is
not required and worse can cause "lost" writes to addresses outside the
address range but part of the cache line. If another component writes to
its part of the cache line between the "clean & invalidate" and
"invalidate" operations, the write can get lost. This fix is to remove
the extra "invalidate" operation when unaligned addressed are used.
A kernel module is available that has a stress test to reproduce the
issue and a unit test of the updated v7_dma_inv_range(). It can be
downloaded from
http://ftp.sageembedded.com/outgoing/linux/cache-test-20181107.tgz.
v7_dma_inv_range() is call by dmac_[un]map_area(addr, len, direction)
when the direction is DMA_FROM_DEVICE. One can (I believe) successfully
argue that DMA from a device to main memory should use buffers aligned
to cache line size, because the "clean & invalidate" might overwrite
data that the device just wrote using DMA. But if a driver does use
unaligned buffers, at least this fix will prevent memory corruption
outside the buffer.
Signed-off-by: Chris Cole <chris@sageembedded.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b603f9e4313348608f256b564ed6e3d9e67f377 ]
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.
This fixes the following build break:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a74515604a7b171f2702bdcbd1e231225fb456d0 ]
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6f32f78645db32b6b95a42e45da2ddd6de0e67 ]
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c3516fed7b61a3527459ccfa67fab130d910610 ]
I noticed that the Android v3.0.8 kernel on droid4 is using different
keypad values from the mainline kernel and does not have issues with
keys occasionally being stuck until pressed again. Turns out there was
an earlier patch posted to fix this as "Input: omap-keypad: errata i689:
Correct debounce time", but it was never reposted to fix use macros
for timing calculations.
This updated version is using macros, and also fixes the use of the
input clock rate to use 32768KiHz instead of 32000KiHz. And we want to
use the known good Android kernel values of 3 and 6 instead of 2 and 6
in the earlier patch.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6dab15f7a79817cab4af612ddd99eda793fce6 ]
SMBus works fine for the touchpad with id SYN3221, used in the HP 15-ay000
series,
This device has been reported in these messages in the "linux-input"
mailing list:
* https://marc.info/?l=linux-input&m=152016683003369&w=2
* https://www.spinics.net/lists/linux-input/msg52525.html
Reported-by: Nitesh Debnath <niteshkd1999@gmail.com>
Reported-by: Teika Kazura <teika@gmx.com>
Signed-off-by: Teika Kazura <teika@gmx.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e85c57493e391b93445c1e0d530b36b95becc64 ]
The > comparison should be >= or we write one element beyond the end of
the unit->clk_table[] array.
(The unit->clk_table[] array is allocated in the mmp_clk_init() function
and it has unit->nr_clks elements).
Fixes: 4661fda10f8b ("clk: mmp: add basic support functions for DT support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f5b7f5dd0fa74a89de5a7ac1e26366f211ccee ]
These > comparisons should be >= to prevent reading beyond the end of
of the clk_data->hws[] buffer.
The clk_data->hws[] array is allocated in cp110_syscon_common_probe()
when we do:
cp110_clk_data = devm_kzalloc(dev, sizeof(*cp110_clk_data) +
sizeof(struct clk_hw *) * CP110_CLK_NUM,
GFP_KERNEL);
As you can see, it has CP110_CLK_NUM elements which is equivalent to
CP110_MAX_CORE_CLOCKS + CP110_MAX_GATABLE_CLOCKS.
Fixes: d3da3eaef7f4 ("clk: mvebu: new driver for Armada CP110 system controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 098336deb946f37a70afc0979af388b615c378bf ]
The error checks on ret for a negative error return always fails because
the return value of iommu_map_sg() is unsigned and can never be negative.
Detected with Coccinelle:
drivers/gpu/drm/msm/msm_iommu.c:69:9-12: WARNING: Unsigned expression
compared with zero: ret < 0
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Rob Clark <robdclark@gmail.com>
CC: David Airlie <airlied@linux.ie>
CC: Julia Lawall <julia.lawall@lip6.fr>
CC: linux-arm-msm@vger.kernel.org
CC: dri-devel@lists.freedesktop.org
CC: freedreno@lists.freedesktop.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a51921c0db3fd26c4ed83dc0ec5d32988fa02aa5 ]
use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dac097c4546e4c5b16dd303a1e97c1d319c8ab3e ]
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place is not doing this, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bd520ab7cf69486ea81fd3cdfd2d5a390ad1100 ]
use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87d81a23e24f24ebe014891e8bdf3ff8785031e8 ]
use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a9a4304f3614e25d9de9b63502ca633c01c0d70 ]
If an asynchronous connection attempt completes while another task is
in xprt_connect(), then the call to rpc_sleep_on() could end up
racing with the call to xprt_wake_pending_tasks().
So add a second test of the connection state after we've put the
task to sleep and set the XPRT_CONNECTING flag, when we know that there
can be no asynchronous connection attempts still in progress.
Fixes: 0b9e79431377d ("SUNRPC: Move the test for XPRT_CONNECTING into...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c01ac66b38660f2b507ccd0b75d28e3002d56fbb ]
The message got changed a lot time ago.
This was responsible for 36 test case failures on sparc64.
Fixes: f1174f77b50c ("bpf/verifier: rework value tracking")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
