commit 9a936d6c3d3d6c33ecbadf72dccdb567b5cd3c72 upstream.
Correct big-endian accesses to the CBUS UART, a Malta on-board discrete
TI16C550C part wired directly to the system controller's device bus, and
do not use byte swapping with the 32-bit accesses to the device.
The CBUS is used for devices such as the boot flash memory needed early
on in system bootstrap even before PCI has been initialised. Therefore
it uses the system controller's device bus, which follows the endianness
set with the CPU, which means no byte-swapping is ever required for data
accesses to CBUS, unlike with PCI.
The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping
with PCI systems. Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.
As it happens the UPIO_MEM32BE access method makes use of the `ioread32'
and `iowrite32' MMIO accessors, which still use `readl' and `writel'
respectively, however they byte-swap data passed, effectively cancelling
swapping done with the accessors themselves and making it suitable for
the CBUS UART.
Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then,
based on the endianness selected. With this change in place the device
is correctly recognised with big-endian Malta at boot, along with the
Super I/O devices behind PCI:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Fixes: e7c4782f92fc ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence")
Cc: stable@vger.kernel.org # v2.6.23+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 877ba3f729fd3d8ef0e29bc2a55e57cfa54b2e43 upstream.
Commit b5776e7524af ("ext4: fix potential htree index checksum
corruption) removed a required restart when multiple levels of index
nodes need to be split. Fix this to avoid directory htree corruptions
when using the large_dir feature.
Cc: stable@kernel.org # v5.11
Cc: Благодаренко Артём <artem.blagodarenko@gmail.com>
Fixes: b5776e7524af ("ext4: fix potential htree index checksum corruption)
Reported-by: Denis <denis@voxelsoft.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46c4c9d1beb7f5b4cec4dd90e7728720583ee348 upstream.
This program always prints 4096 and hangs before the patch, and always
prints 8192 and exits successfully after:
int main()
{
int pipefd[2];
for (int i = 0; i < 1025; i++)
if (pipe(pipefd) == -1)
return 1;
size_t bufsz = fcntl(pipefd[1], F_GETPIPE_SZ);
printf("%zd\n", bufsz);
char *buf = calloc(bufsz, 1);
write(pipefd[1], buf, bufsz);
read(pipefd[0], buf, bufsz-1);
write(pipefd[1], buf, 1);
}
Note that you may need to increase your RLIMIT_NOFILE before running the
program.
Fixes: 759c01142a ("pipe: limit the per-user amount of pages allocated in pipes")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/lkml/1628086770.5rn8p04n6j.none@localhost/
Link: https://lore.kernel.org/lkml/1628127094.lxxn016tj7.none@localhost/
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f22c93b209c811bd489950f17f8839adb31901 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com
Reported-by: Eero Lehtinen <debiangamer2@gmail.com>
Tested-by: Eero Lehtinen <debiangamer2@gmail.com>
Fixes: d0f232e823af ("[media] rtl28xxu: add heuristic to detect chip type")
Cc: stable@vger.kernel.org # 4.0
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6f1488abeca594d377991171c00e52a upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa20bada3f934e3b3e4af4c77e5b518cd5a282e5 upstream.
SET_IDLE value must be shifted 8 bits to the right to get duration.
This confirmed by USBCV test.
Fixes: afcff6dc690e ("usb: gadget: f_hid: added GET_IDLE and SET_IDLE handlers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210727185800.43796-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2867652e4766360adf14dfda3832455e04964f2a upstream.
Disconnecting and reconnecting the USB cable can lead to crashes
and a variety of kernel log spam.
The problem was found and reproduced on the Raspberry Pi [1]
and the original fix was created in Raspberry's own fork [2].
Link: https://github.com/raspberrypi/linux/issues/3870 [1]
Link: a6e47d5f4e [2]
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210723155928.210019-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afcff6dc690e24d636a41fd4bee6057e7c70eebd upstream.
The USB HID standard declares mandatory support for GET_IDLE and SET_IDLE
requests for Boot Keyboard. Most hosts can handle their absence, but others
like some old/strange UEFIs and BIOSes consider this a critical error
and refuse to work with f_hid.
This primitive implementation of saving and returning idle is sufficient
to meet the requirements of the standard and these devices.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210721180351.129450-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8da0e55c7988ef9f08a708c38e5c75ecd8862cf8 upstream.
The Auto-M3 OP-COM v2 is a OBD diagnostic device using a FTD232 for the
USB connection.
Signed-off-by: David Bauer <mail@david-bauer.net>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c18e9baee0ef97510dcda78c82285f52626764b upstream.
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fad76ce4e98263edfa8f885c81d5426c1bf169 upstream.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 1-...!: (2 ticks this GP) idle=d92/1/0x4000000000000000
softirq=25390/25392 fqs=3
(t=12164 jiffies g=31645 q=43226)
rcu: rcu_preempt kthread starved for 12162 jiffies! g31645 f0x0
RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time,
OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task
...........
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: usb_submit_urb failed: -19
The function usbtmc_interrupt() resubmits urbs when the error status
of an urb is -EPROTO. In systems using the dummy_hcd usb controller
this can result in endless interrupt loops when the usbtmc device is
disconnected from the host system.
Since host controller drivers already try to recover from transmission
errors, there is no need to resubmit the urb or try other solutions
to repair the error situation.
In case of errors the INT pipe just stops to wait for further packets.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation")
Cc: stable@vger.kernel.org
Reported-by: syzbot+e2eae5639e7203360018@syzkaller.appspotmail.com
Signed-off-by: Qiang.zhang <qiang.zhang@windriver.com>
Acked-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Link: https://lore.kernel.org/r/20210723004334.458930-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e04480920d1eec9c061841399aa6f35b6f987d8b ]
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743ee8 ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a8e ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f81b ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e678b ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e678b ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942e560a3d3862dd5dee1411dbdd7097d29b8416 ]
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362b4 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44712965bf12ae1758cec4de53816ed4b914ca1a ]
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba21 ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af35fc37354cda3c9c8cc4961b1d24bdc9d27903 ]
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb653827c758725b149b5c924a5eb50ab4812750 ]
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc89365e ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28bbbb9875a35975904e46f9b06fa689d051b290 ]
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d245f ("[MIPS] There is no __GNUC_MAJOR__")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdc5d85a8fe684cdf24dc31c6bc4a727decfe87 ]
Pauseframe control is set to symmetric mode by default on the NFP.
Pause frames can not be configured through ethtool now, but ethtool can
report the supported mode.
Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe74dfd41c428afb24e2e615470832fa997ff14 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592b46907adbeb81243f7eb7a468c36692658b8 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201bb ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c04243a56a7977185b00400e59ca7e108004faf ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59d6 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad180e09805fa46965d15e1dfadf09ffa5 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b5b1978cd5a80db58e2a19db2f9c36fe8d4f7a ]
Enabling the framebuffer leads to a system hang. Running, as a debug
hack, the store_pan() function in drivers/video/fbdev/core/fbsysfs.c
without taking the console_lock, allows to see the crash backtrace on
the serial line.
~ # echo 0 0 > /sys/class/graphics/fb0/pan
[ 9.719414] Unhandled exception: IPSR = 00000005 LR = fffffff1
[ 9.726937] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.733008] Hardware name: STM32 (Device Tree Support)
[ 9.738296] PC is at clk_gate_is_enabled+0x0/0x28
[ 9.743426] LR is at stm32f4_pll_div_set_rate+0xf/0x38
[ 9.748857] pc : [<0011e4be>] lr : [<0011f9e3>] psr: 0100000b
[ 9.755373] sp : 00bc7be0 ip : 00000000 fp : 001f3ac4
[ 9.760812] r10: 002610d0 r9 : 01efe920 r8 : 00540560
[ 9.766269] r7 : 02e7ddb0 r6 : 0173eed8 r5 : 00000000 r4 : 004027c0
[ 9.773081] r3 : 0011e4bf r2 : 02e7ddb0 r1 : 0173eed8 r0 : 1d3267b8
[ 9.779911] xPSR: 0100000b
[ 9.782719] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.788791] Hardware name: STM32 (Device Tree Support)
[ 9.794120] [<0000afa1>] (unwind_backtrace) from [<0000a33f>] (show_stack+0xb/0xc)
[ 9.802421] [<0000a33f>] (show_stack) from [<0000a8df>] (__invalid_entry+0x4b/0x4c)
The `pll_num' field in the post_div_data configuration contained a wrong
value which also referenced an uninitialized hardware clock when
clk_register_pll_div() was called.
Fixes: 517633ef630e ("clk: stm32f4: Add post divisor for I2S & SAI PLLs")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Link: https://lore.kernel.org/r/20210725160725.10788-1-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c97226aab8b298ada954ce12659ee3ad2a4 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6511a8b5b7a65037340cd8ee91a377811effbc83 upstream.
Revert commit c27bac0314131 ("ACPICA: Fix memory leak caused by _CID
repair function") which is reported to cause a boot issue on Acer
Swift 3 (SF314-51).
Reported-by: Adrien Precigout <dev@asdrip.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5c3954b35eddff0da0436c31e8d721eceb7dc2 upstream.
Commit 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cb1bdbfad648aa32c43bec6ef6d03e1c9d434393 which is
commit cb011044e34c293e139570ce5c01aed66a34345c upstream.
It is reported to cause problems with systems and probably should not
have been backported in the first place :(
Link: https://lore.kernel.org/r/20210803165108.4154cd52@endymion
Reported-by: Jean Delvare <jdelvare@suse.de>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9545779ee9e9e103648f6f2552e73cfe808d0f4 upstream.
Use kvm_pfn_t, a.k.a. u64, for the local 'pfn' variable when retrieving
a so called "remapped" hva/pfn pair. In theory, the hva could resolve to
a pfn in high memory on a 32-bit kernel.
This bug was inadvertantly exposed by commit bd2fae8da794 ("KVM: do not
assume PTE is writable after follow_pfn"), which added an error PFN value
to the mix, causing gcc to comlain about overflowing the unsigned long.
arch/x86/kvm/../../../virt/kvm/kvm_main.c: In function ‘hva_to_pfn_remapped’:
include/linux/kvm_host.h:89:30: error: conversion from ‘long long unsigned int’
to ‘long unsigned int’ changes value from
‘9218868437227405314’ to ‘2’ [-Werror=overflow]
89 | #define KVM_PFN_ERR_RO_FAULT (KVM_PFN_ERR_MASK + 2)
| ^
virt/kvm/kvm_main.c:1935:9: note: in expansion of macro ‘KVM_PFN_ERR_RO_FAULT’
Cc: stable@vger.kernel.org
Fixes: add6a0cd1c5b ("KVM: MMU: try to fix up page faults before giving up")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210208201940.1258328-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8be156be163a052a067306417cd0ff679068c97 upstream.
It's possible to create a region which maps valid but non-refcounted
pages (e.g., tail pages of non-compound higher order allocations). These
host pages can then be returned by gfn_to_page, gfn_to_pfn, etc., family
of APIs, which take a reference to the page, which takes it from 0 to 1.
When the reference is dropped, this will free the page incorrectly.
Fix this by only taking a reference on valid pages if it was non-zero,
which indicates it is participating in normal refcounting (and can be
released with put_page).
This addresses CVE-2021-22543.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd2fae8da794b55bf2ac02632da3a151b10e664c upstream.
In order to convert an HVA to a PFN, KVM usually tries to use
the get_user_pages family of functinso. This however is not
possible for VM_IO vmas; in that case, KVM instead uses follow_pfn.
In doing this however KVM loses the information on whether the
PFN is writable. That is usually not a problem because the main
use of VM_IO vmas with KVM is for BARs in PCI device assignment,
however it is a bug. To fix it, use follow_pte and check pte_write
while under the protection of the PTE lock. The information can
be used to fail hva_to_pfn_remapped or passed back to the
caller via *writable.
Usage of follow_pfn was introduced in commit add6a0cd1c5b ("KVM: MMU: try to fix
up page faults before giving up", 2016-07-05); however, even older version
have the same issue, all the way back to commit 2e2e3738af33 ("KVM:
Handle vma regions with no backing page", 2008-07-20), as they also did
not check whether the PFN was writable.
Fixes: 2e2e3738af33 ("KVM: Handle vma regions with no backing page")
Reported-by: David Stevens <stevensd@google.com>
Cc: 3pvd@google.com
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[OP: backport to 4.14, adjust follow_pte() -> follow_pte_pmd()]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a17ad0961706244dce48ec941f7e476a38c0e727 ]
In some cases skb head could be locked and entire header
data is pulled from skb. When skb_zerocopy() called in such cases,
following BUG is triggered. This patch fixes it by copying entire
skb in such cases.
This could be optimized incase this is performance bottleneck.
---8<---
kernel BUG at net/core/skbuff.c:2961!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:skb_zerocopy+0x37a/0x3a0
RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246
Call Trace:
<IRQ>
queue_userspace_packet+0x2af/0x5e0 [openvswitch]
ovs_dp_upcall+0x3d/0x60 [openvswitch]
ovs_dp_process_packet+0x125/0x150 [openvswitch]
ovs_vport_receive+0x77/0xd0 [openvswitch]
netdev_port_receive+0x87/0x130 [openvswitch]
netdev_frame_hook+0x4b/0x60 [openvswitch]
__netif_receive_skb_core+0x2b4/0xc90
__netif_receive_skb_one_core+0x3f/0xa0
__netif_receive_skb+0x18/0x60
process_backlog+0xa9/0x160
net_rx_action+0x142/0x390
__do_softirq+0xe1/0x2d6
irq_exit+0xae/0xb0
do_IRQ+0x5a/0xf0
common_interrupt+0xf/0xf
Code that triggered BUG:
int
skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen)
{
int i, j = 0;
int plen = 0; /* length of skb->head fragment */
int ret;
struct page *page;
unsigned int offset;
BUG_ON(!from->head_frag && !hlen);
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6206b7981a36476f4695d661ae139f7db36a802d ]
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ
QL41000 ethernet controller:
BUG: scheduling while atomic: kworker/0:4/531/0x00000200
[qed_probe:488()]hw prepare failed
kernel BUG at mm/vmalloc.c:2355!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu
pstate: 00400009 (nzcv daif +PAN -UAO)
Call trace:
vunmap+0x4c/0x50
iounmap+0x48/0x58
qed_free_pci+0x60/0x80 [qed]
qed_probe+0x35c/0x688 [qed]
__qede_probe+0x88/0x5c8 [qede]
qede_probe+0x60/0xe0 [qede]
local_pci_probe+0x48/0xa0
work_for_cpu_fn+0x24/0x38
process_one_work+0x1d0/0x468
worker_thread+0x238/0x4e0
kthread+0xf0/0x118
ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in
theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in
_qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang <Lijian.Zhang@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c23aa51477a37f8b56c3c40192248db0663c196 ]
rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits. This may lead to
the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6549c46af8551b346bcc0b9043f93848319acd5c ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f.
If value is from 20 to 31, the voltage will all be fixed to 3V.
And LDO also, just vout range is different from 1.2v to 3v, step is the
same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 240246f6b913b0c23733cfd2def1d283f8cc9bbe ]
In compression write endio sequence, the range which the compressed_bio
writes is marked as uptodate if the last bio of the compressed (sub)bios
is completed successfully. There could be previous bio which may
have failed which is recorded in cb->errors.
Set the writeback range as uptodate only if cb->errors is zero, as opposed
to checking only the last bio's status.
Backporting notes: in all versions up to 4.4 the last argument is always
replaced by "!cb->errors".
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9bac1bd6e6d36459087a728a968e79e37ebcea1a upstream.
This makes 'perf top' abort in some cases, and the right fix will
involve surgery that is too much to do at this stage, so revert for now
and fix it in the next merge window.
This reverts commit 2d6b74baa7147251c30a46c4996e8cc224aa2dc5.
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6b3c7848e66e9046c8a79a5b88fd03461cc252b ]
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/r/20210729141246.GA1267@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89fb62fde3b226f99b7015280cf132e2a7438edf ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76a16be07b209a3f507c72abe823bd3af1c8661a ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 557fb5862c9272ad9b21407afe1da8acfd9b53eb ]
As Ben Hutchings noticed, this check should have been inverted: the call
returns true in case of success.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 0c5dc070ff3d ("sctp: validate from_addr_param return")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b54874ef1617185048029a3083d510569e93751 ]
Fix a bug when flow table is created in priority that already
has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority,
we need to connect the flow tables from the previous priority (p0)
to this new table. In addition when this flow table is destroyed
(FT-B), we need to connect the flow tables from the previous
priority (p0) to the next level flow table (FT-C) in the same
priority of the destroyed table (if exists).
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)-x| | p-y | | p-n |
---------- ---------- ---------
| |
---------------- ------------------
|ns(e.g bypass)| |ns(e.g. kernel) |
---------------- ------------------
| | |
------- ------ ----
| p0 | | p1 | |p2|
------- ------ ----
| | \
-------- ------- ------
| FT-A | |FT-B | |FT-C|
-------- ------- ------
Fixes: f90edfd279f3 ("net/mlx5_core: Connect flow tables")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c9d2102c9c098916ab9e0ab248006107d00d6c ]
Syzbot reported skb_over_panic() in llc_pdu_init_as_xid_cmd(). The
problem was in wrong LCC header manipulations.
Syzbot's reproducer tries to send XID packet. llc_ui_sendmsg() is
doing following steps:
1. skb allocation with size = len + header size
len is passed from userpace and header size
is 3 since addr->sllc_xid is set.
2. skb_reserve() for header_len = 3
3. filling all other space with memcpy_from_msg()
Ok, at this moment we have fully loaded skb, only headers needs to be
filled.
Then code comes to llc_sap_action_send_xid_c(). This function pushes 3
bytes for LLC PDU header and initializes it. Then comes
llc_pdu_init_as_xid_cmd(). It initalizes next 3 bytes *AFTER* LLC PDU
header and call skb_push(skb, 3). This looks wrong for 2 reasons:
1. Bytes rigth after LLC header are user data, so this function
was overwriting payload.
2. skb_push(skb, 3) call can cause skb_over_panic() since
all free space was filled in llc_ui_sendmsg(). (This can
happen is user passed 686 len: 686 + 14 (eth header) + 3 (LLC
header) = 703. SKB_DATA_ALIGN(703) = 704)
So, in this patch I added 2 new private constansts: LLC_PDU_TYPE_U_XID
and LLC_PDU_LEN_U_XID. LLC_PDU_LEN_U_XID is used to correctly reserve
header size to handle LLC + XID case. LLC_PDU_TYPE_U_XID is used by
llc_pdu_header_init() function to push 6 bytes instead of 3. And finally
I removed skb_push() call from llc_pdu_init_as_xid_cmd().
This changes should not affect other parts of LLC, since after
all steps we just transmit buffer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+5e5a981ad7cc54c4b2b4@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e4960b3d66d7248b23de3251118147812b42da2 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'err'.
Eliminate the follow smatch warning:
drivers/net/ethernet/mellanox/mlx4/main.c:3538 mlx4_load_one() warn:
missing error code 'err'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7ae0e400cd93 ("net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
