[ Upstream commit 9e311820f67e740f4fb8dcb82b4c4b5b05bdd1a5 ]
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3885f576196ddfc670b3d53e745de96ffcb49ab ]
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 865ad2f2201dc18685ba2686f13217f8b3a9c52c ]
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 457bfc0a4bf531487ecc3cf82ec728a5e114fb1e ]
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d3ca681b9d9575ccf696ebc2840a1ebb1fd4074 ]
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73d527aef68f7644e59f22ce7f9ac75e7b533aea ]
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22e984493a41bf8081f13d9ed84def3ca8cfd427 ]
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583a3638dc07cc1878f41265e85ed497f72efcb ]
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78f7a7566f5eb59321e99b55a6fdb16ea05b37d1 ]
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6bce2137f5d6bb1093e96d2f801479099b28094 ]
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e0caab8e0f96f0af7d1dd388e62f44184a75372 ]
The optee driver uses specific page table types to verify if a memory
region is normal. These types are not defined in nommu systems. Trying
to compile the driver in these systems results in a build error:
linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’:
linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared
(first use in this function); did you mean ‘PREEMPT_MASK’?
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~
PREEMPT_MASK
linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is
reported only once for each function it appears in
linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared
(first use in this function)
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~~~~~~~
Make the optee driver depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[jw: update commit title]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6849b5eba1965ceb0cad3a75877ef4569dd3638e ]
Updates to the Generic Timer architecture allow ID_PFR1.GenTimer to
have values other than 0 or 1 while still preserving backward
compatibility. At the moment, Linux is quite strict in the way it
handles this field at early boot and will not configure arch timer if
it doesn't find the value 1.
Since here use ubfx for arch timer version extraction (hyb-stub build
with -march=armv7-a, so it is safe)
To help backports (even though the code was correct at the time of writing)
Fixes: 8ec58be9f3ff ("ARM: virt: arch_timers: enable access to physical timers")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e2209629fec427ba75a6351486153a9feddd36b ]
When a link is going down the driver will be calling fnic_cleanup_io(),
which will traverse all commands and calling 'done' for each found command.
While the traversal is handled under the host_lock, calling 'done' happens
after the host_lock is being dropped.
As fnic_queuecommand_lck() is being called with the host_lock held, it
might well be that it will pick the command being selected for abortion
from the above routine and enqueue it for sending, but then 'done' is being
called on that very command from the above routine.
Which of course confuses the hell out of the scsi midlayer.
So fix this by not queueing commands when fnic_cleanup_io is active.
Link: https://lore.kernel.org/r/20200116102053.62755-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95224166a9032ff5d08fca633d37113078ce7d01 ]
With an ebpf program that redirects packets through a vti[6] interface,
the packets are dropped because no dst is attached.
This could also be reproduced with an AF_PACKET socket, with the following
python script (vti1 is an ip_vti interface):
import socket
send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0)
# scapy
# p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request')
# raw(p)
req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00'
send_s.sendto(req, ('vti1', 0x800, 0, 0))
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5abd45ea0fc3060f7805e131753fdcbafd6c6618 ]
BeagleBone Black series is equipped with 512MB RAM
whereas only 256MB is included from am335x-bone-common.dtsi
This leads to an issue with unusual setups when devicetree
is loaded by GRUB2 directly.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fc7caa84e713f7627e171ab1e7c4b5be0dc9b3d ]
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f1880cbe8d0d49ebb7e9ae409b3b96676e5aa97 ]
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16119655c9e6c4aa5767cd971baa9c491f41b13 ]
After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:
In function 'iw_handler_get_iwstats',
inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
memcpy(extra, stats, sizeof(struct iw_statistics));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here
The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.
Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f601265215a421f425ba3a4850a35861d024643 ]
TKIP replay protection was skipped for the very first frame received
after a new key is configured. While this is potentially needed to avoid
dropping a frame in some cases, this does leave a window for replay
attacks with group-addressed frames at the station side. Any earlier
frame sent by the AP using the same key would be accepted as a valid
frame and the internal RSC would then be updated to the TSC from that
frame. This would allow multiple previously transmitted group-addressed
frames to be replayed until the next valid new group-addressed frame
from the AP is received by the station.
Fix this by limiting the no-replay-protection exception to apply only
for the case where TSC=0, i.e., when this is for the very first frame
protected using the new key, and the local RSC had not been set to a
higher value when configuring the key (which may happen with GTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20200107153545.10934-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26ec17a1dc5ecdd8d91aba63ead6f8b5ad5dea0d ]
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4b9d655e445a8be0bff624aedea190606b5ebbc ]
Commit e33e2241e272 ("Revert "cfg80211: Use 5MHz bandwidth by
default when checking usable channels"") fixed a broken
regulatory (leaving channel 12 open for AP where not permitted).
Apply a similar fix to custom regulatory domain processing.
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Link: https://lore.kernel.org/r/1576836859-8945-1-git-send-email-ganapathi.bhat@nxp.com
[reword commit message, fix coding style, add a comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ff44f0e61d074f29770413fef6a5452be7b83e ]
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5365ec1aeff5b9f2962a9c9b31d63f9dad7e0e2d ]
Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.
Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.
Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fad78ad6422d9bca62135bbed8b6abc4cbb85b8 ]
This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.
The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa604651d523b1493988d0bf6710339f3ee60272 ]
Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.
Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bea5ac0fbc5b2103f8779ddff216122e3c2e1ad ]
Determined empirically, no documentation is available.
The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock")'
Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03729cfa0d543bc996bf959e762ec999afc8f3d2 ]
Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.
To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e17e7c498d4f734df93c300441e100818ed58168 ]
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c226017d3ec93547b58082bdf778d9db7401c95 ]
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
A pointer to 'struct si470x_device' is currently used after free:
drivers/media/radio/si470x/radio-si470x-i2c.c:462:25-30: ERROR: reference
preceded by free on line 460
Shift the call to free() down past its final use.
NB: Not sending to Mainline, since the problem does not exist there, it was
caused by the backport of 2df200ab234a ("media: si470x-i2c: add missed
operations in remove") to the stable trees.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bc0bb36fa30e95ca829e9cf480e1ef7f7638333 upstream.
The test_cgcore_no_internal_process_constraint_on_threads selftest when
running with subsystem controlling noise triggers two warnings:
> [ 597.443115] WARNING: CPU: 1 PID: 28167 at kernel/cgroup/cgroup.c:3131 cgroup_apply_control_enable+0xe0/0x3f0
> [ 597.443413] WARNING: CPU: 1 PID: 28167 at kernel/cgroup/cgroup.c:3177 cgroup_apply_control_disable+0xa6/0x160
Both stem from a call to cgroup_type_write. The first warning was also
triggered by syzkaller.
When we're switching cgroup to threaded mode shortly after a subsystem
was disabled on it, we can see the respective subsystem css dying there.
The warning in cgroup_apply_control_enable is harmless in this case
since we're not adding new subsys anyway.
The warning in cgroup_apply_control_disable indicates an attempt to kill
css of recently disabled subsystem repeatedly.
The commit prevents these situations by making cgroup_type_write wait
for all dying csses to go away before re-applying subtree controls.
When at it, the locations of WARN_ON_ONCE calls are moved so that
warning is triggered only when we are about to misuse the dying css.
Reported-by: syzbot+5493b2a54d31d6aea629@syzkaller.appspotmail.com
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11eb85ec42dc8c7a7ec519b90ccf2eeae9409de8 upstream.
Syzbot managed to trigger a use after free "KASAN: use-after-free Write
in hci_sock_bind". I have reviewed the code manually and one possibly
cause I have found is that we are not holding lock_sock(sk) when we do
the hci_dev_put(hdev) in hci_sock_release(). My theory is that the bind
and the release are racing against each other which results in this use
after free.
Reported-by: syzbot+eba992608adf3d796bcc@syzkaller.appspotmail.com
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a655c77ff8fc65699a3f98e237db563b37c439b upstream.
tpk_write()/tpk_close() could be interrupted when holding a mutex, then
in timer handler tpk_write() may be called again trying to acquire same
mutex, lead to deadlock.
Google syzbot reported this issue with CONFIG_DEBUG_ATOMIC_SLEEP
enabled:
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:938
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/1
1 lock held by swapper/1/0:
...
Call Trace:
<IRQ>
dump_stack+0x197/0x210
___might_sleep.cold+0x1fb/0x23e
__might_sleep+0x95/0x190
__mutex_lock+0xc5/0x13c0
mutex_lock_nested+0x16/0x20
tpk_write+0x5d/0x340
resync_tnc+0x1b6/0x320
call_timer_fn+0x1ac/0x780
run_timer_softirq+0x6c3/0x1790
__do_softirq+0x262/0x98c
irq_exit+0x19b/0x1e0
smp_apic_timer_interrupt+0x1a3/0x610
apic_timer_interrupt+0xf/0x20
</IRQ>
See link https://syzkaller.appspot.com/bug?extid=2eeef62ee31f9460ad65 for
more details.
Fix it by using spinlock in process context instead of mutex and having
interrupt disabled in critical section.
Reported-by: syzbot+2eeef62ee31f9460ad65@syzkaller.appspotmail.com
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200113034842.435-1-zhenzhong.duan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 569bc8d6a6a50acb5fcf07fb10b8d2d461fdbf93 upstream.
This fixes a syzbot failure since actlen could be uninitialized,
but it was still used.
Syzbot link:
https://syzkaller.appspot.com/bug?extid=6bf9606ee955b646c0e1
Reported-and-tested-by: syzbot+6bf9606ee955b646c0e1@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51d0c99b391f0cac61ad7b827c26f549ee55672c upstream.
If usb_bulk_msg() fails, actual_length can be uninitialized.
Reported-by: syzbot+9d42b7773d2fecd983ab@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eecc70d22ae51225de1ef629c1159f7116476b2e upstream.
This results in an uninitialized variable read.
Reported-by: syzbot+6bf9606ee955b646c0e1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5474ca7da6f34fa95e82edc747d5faa19cbdfb5c upstream.
When a filesystem is mounted with jdev mount option, we store the
journal device name in an allocated string in superblock. However we
fail to ever free that string. Fix it.
Reported-by: syzbot+1c6756baf4b16b94d2a6@syzkaller.appspotmail.com
Fixes: c3aa077648e1 ("reiserfs: Properly display mount options in /proc/mounts")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7a91bc7c2e17e0a9c8b9745a2cb118891218fd1 upstream.
What we are trying to do is change the '=' character to a NUL terminator
and then at the end of the function we restore it back to an '='. The
problem is there are two error paths where we jump to the end of the
function before we have replaced the '=' with NUL.
We end up putting the '=' in the wrong place (possibly one element
before the start of the buffer).
Link: http://lkml.kernel.org/r/20200115055426.vdjwvry44nfug7yy@kili.mountain
Reported-by: syzbot+e64a13c5369a194d67df@syzkaller.appspotmail.com
Fixes: 095f1fc4ebf3 ("mempolicy: rework shmem mpol parsing and display")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Dmitry Vyukov <dvyukov@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9803387c55f7d2ce69aa64340c5fdc6b3027dbc8 upstream.
Instead of setting s_want_extra_size and then making sure that it is a
valid value afterwards, validate the field before we set it. This
avoids races and other problems when remounting the file system.
Link: https://lore.kernel.org/r/20191215063020.GA11512@mit.edu
Cc: stable@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-and-tested-by: syzbot+4a39a025912b265cacef@syzkaller.appspotmail.com
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7bbd6c1b01cb5dd13c245d4586a83145c1d5f52 upstream.
Since v4.3-rc1 commit 0723c05fb75e44 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb75e44 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c4798d3f08b81c2c52936b10e0fa872590c96ae upstream.
Disable a couple of compilation warnings (which are treated as errors)
on strlcpy() definition and declaration, allowing users to compile perf
and kernel (objtool) when:
1. glibc have strlcpy() (such as in ALT Linux since 2004) objtool and
perf build fails with this (in gcc):
In file included from exec-cmd.c:3:
tools/include/linux/string.h:20:15: error: redundant redeclaration of ‘strlcpy’ [-Werror=redundant-decls]
20 | extern size_t strlcpy(char *dest, const char *src, size_t size);
2. clang ignores `-Wredundant-decls', but produces another warning when
building perf:
CC util/string.o
../lib/string.c:99:8: error: attribute declaration must precede definition [-Werror,-Wignored-attributes]
size_t __weak strlcpy(char *dest, const char *src, size_t size)
../../tools/include/linux/compiler.h:66:34: note: expanded from macro '__weak'
# define __weak __attribute__((weak))
/usr/include/bits/string_fortified.h:151:8: note: previous definition is here
__NTH (strlcpy (char *__restrict __dest, const char *__restrict __src,
Committer notes:
The
#pragma GCC diagnostic
directive was introduced in gcc 4.6, so check for that as well.
Fixes: ce99091 ("perf tools: Move strlcpy() from perf to tools/lib/string.c")
Fixes: 0215d59 ("tools lib: Reinstate strlcpy() header guard with __UCLIBC__")
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=118481
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Dmitry Levin <ldv@altlinux.org>
Cc: Dmitry Levin <ldv@altlinux.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: kbuild test robot <lkp@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Cc: Vineet Gupta <vineet.gupta1@synopsys.com>
Link: http://lore.kernel.org/lkml/20191224172029.19690-1-vt@altlinux.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fee1a7cc6b1ce6634bb0f025be2c94a58dfa34d upstream.
The commit 4585fbcb5331 ("PM / devfreq: Modify the device name as devfreq(X) for
sysfs") changed the node name to devfreq(x). After this commit, it is not
possible to get the device name through /sys/class/devfreq/devfreq(X)/*.
Add new name attribute in order to get device name.
Cc: stable@vger.kernel.org
Fixes: 4585fbcb5331 ("PM / devfreq: Modify the device name as devfreq(X) for sysfs")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07bfd9bdf568a38d9440c607b72342036011f727 ]
On module unload of pcrypt we must unregister the crypto algorithms
first and then tear down the padata structure. As otherwise the
crypto algorithms are still alive and can be used while the padata
structure is being freed.
Fixes: 5068c7a883d1 ("crypto: pcrypt - Add pcrypt crypto...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 334b0f4e9b1b4a1d475f803419d202f6c5e4d18e upstream.
There is a race condition which results in a deadlock when rmdir and
mkdir execute concurrently:
$ ls /sys/fs/resctrl/c1/mon_groups/m1/
cpus cpus_list mon_data tasks
Thread 1: rmdir /sys/fs/resctrl/c1
Thread 2: mkdir /sys/fs/resctrl/c1/mon_groups/m1
3 locks held by mkdir/48649:
#0: (sb_writers#17){.+.+}, at: [<ffffffffb4ca2aa0>] mnt_want_write+0x20/0x50
#1: (&type->i_mutex_dir_key#8/1){+.+.}, at: [<ffffffffb4c8c13b>] filename_create+0x7b/0x170
#2: (rdtgroup_mutex){+.+.}, at: [<ffffffffb4a4389d>] rdtgroup_kn_lock_live+0x3d/0x70
4 locks held by rmdir/48652:
#0: (sb_writers#17){.+.+}, at: [<ffffffffb4ca2aa0>] mnt_want_write+0x20/0x50
#1: (&type->i_mutex_dir_key#8/1){+.+.}, at: [<ffffffffb4c8c3cf>] do_rmdir+0x13f/0x1e0
#2: (&type->i_mutex_dir_key#8){++++}, at: [<ffffffffb4c86d5d>] vfs_rmdir+0x4d/0x120
#3: (rdtgroup_mutex){+.+.}, at: [<ffffffffb4a4389d>] rdtgroup_kn_lock_live+0x3d/0x70
Thread 1 is deleting control group "c1". Holding rdtgroup_mutex,
kernfs_remove() removes all kernfs nodes under directory "c1"
recursively, then waits for sub kernfs node "mon_groups" to drop active
reference.
Thread 2 is trying to create a subdirectory "m1" in the "mon_groups"
directory. The wrapper kernfs_iop_mkdir() takes an active reference to
the "mon_groups" directory but the code drops the active reference to
the parent directory "c1" instead.
As a result, Thread 1 is blocked on waiting for active reference to drop
and never release rdtgroup_mutex, while Thread 2 is also blocked on
trying to get rdtgroup_mutex.
Thread 1 (rdtgroup_rmdir) Thread 2 (rdtgroup_mkdir)
(rmdir /sys/fs/resctrl/c1) (mkdir /sys/fs/resctrl/c1/mon_groups/m1)
------------------------- -------------------------
kernfs_iop_mkdir
/*
* kn: "m1", parent_kn: "mon_groups",
* prgrp_kn: parent_kn->parent: "c1",
*
* "mon_groups", parent_kn->active++: 1
*/
kernfs_get_active(parent_kn)
kernfs_iop_rmdir
/* "c1", kn->active++ */
kernfs_get_active(kn)
rdtgroup_kn_lock_live
atomic_inc(&rdtgrp->waitcount)
/* "c1", kn->active-- */
kernfs_break_active_protection(kn)
mutex_lock
rdtgroup_rmdir_ctrl
free_all_child_rdtgrp
sentry->flags = RDT_DELETED
rdtgroup_ctrl_remove
rdtgrp->flags = RDT_DELETED
kernfs_get(kn)
kernfs_remove(rdtgrp->kn)
__kernfs_remove
/* "mon_groups", sub_kn */
atomic_add(KN_DEACTIVATED_BIAS, &sub_kn->active)
kernfs_drain(sub_kn)
/*
* sub_kn->active == KN_DEACTIVATED_BIAS + 1,
* waiting on sub_kn->active to drop, but it
* never drops in Thread 2 which is blocked
* on getting rdtgroup_mutex.
*/
Thread 1 hangs here ---->
wait_event(sub_kn->active == KN_DEACTIVATED_BIAS)
...
rdtgroup_mkdir
rdtgroup_mkdir_mon(parent_kn, prgrp_kn)
mkdir_rdt_prepare(parent_kn, prgrp_kn)
rdtgroup_kn_lock_live(prgrp_kn)
atomic_inc(&rdtgrp->waitcount)
/*
* "c1", prgrp_kn->active--
*
* The active reference on "c1" is
* dropped, but not matching the
* actual active reference taken
* on "mon_groups", thus causing
* Thread 1 to wait forever while
* holding rdtgroup_mutex.
*/
kernfs_break_active_protection(
prgrp_kn)
/*
* Trying to get rdtgroup_mutex
* which is held by Thread 1.
*/
Thread 2 hangs here ----> mutex_lock
...
The problem is that the creation of a subdirectory in the "mon_groups"
directory incorrectly releases the active protection of its parent
directory instead of itself before it starts waiting for rdtgroup_mutex.
This is triggered by the rdtgroup_mkdir() flow calling
rdtgroup_kn_lock_live()/rdtgroup_kn_unlock() with kernfs node of the
parent control group ("c1") as argument. It should be called with kernfs
node "mon_groups" instead. What is currently missing is that the
kn->priv of "mon_groups" is NULL instead of pointing to the rdtgrp.
Fix it by pointing kn->priv to rdtgrp when "mon_groups" is created. Then
it could be passed to rdtgroup_kn_lock_live()/rdtgroup_kn_unlock()
instead. And then it operates on the same rdtgroup structure but handles
the active reference of kernfs node "mon_groups" to prevent deadlock.
The same changes are also made to the "mon_data" directories.
This results in some unused function parameters that will be cleaned up
in follow-up patch as the focus here is on the fix only in support of
backporting efforts.
Backporting notes:
Since upstream commit fa7d949337cc ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
for older stable trees.
Fixes: c7d9aac61311 ("x86/intel_rdt/cqm: Add mkdir support for RDT monitoring")
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1578500886-21771-4-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 074fadee59ee7a9d2b216e9854bd4efb5dad679f upstream.
There is a race condition in the following scenario which results in an
use-after-free issue when reading a monitoring file and deleting the
parent ctrl_mon group concurrently:
Thread 1 calls atomic_inc() to take refcount of rdtgrp and then calls
kernfs_break_active_protection() to drop the active reference of kernfs
node in rdtgroup_kn_lock_live().
In Thread 2, kernfs_remove() is a blocking routine. It waits on all sub
kernfs nodes to drop the active reference when removing all subtree
kernfs nodes recursively. Thread 2 could block on kernfs_remove() until
Thread 1 calls kernfs_break_active_protection(). Only after
kernfs_remove() completes the refcount of rdtgrp could be trusted.
Before Thread 1 calls atomic_inc() and kernfs_break_active_protection(),
Thread 2 could call kfree() when the refcount of rdtgrp (sentry) is 0
instead of 1 due to the race.
In Thread 1, in rdtgroup_kn_unlock(), referring to earlier rdtgrp memory
(rdtgrp->waitcount) which was already freed in Thread 2 results in
use-after-free issue.
Thread 1 (rdtgroup_mondata_show) Thread 2 (rdtgroup_rmdir)
-------------------------------- -------------------------
rdtgroup_kn_lock_live
/*
* kn active protection until
* kernfs_break_active_protection(kn)
*/
rdtgrp = kernfs_to_rdtgroup(kn)
rdtgroup_kn_lock_live
atomic_inc(&rdtgrp->waitcount)
mutex_lock
rdtgroup_rmdir_ctrl
free_all_child_rdtgrp
/*
* sentry->waitcount should be 1
* but is 0 now due to the race.
*/
kfree(sentry)*[1]
/*
* Only after kernfs_remove()
* completes, the refcount of
* rdtgrp could be trusted.
*/
atomic_inc(&rdtgrp->waitcount)
/* kn->active-- */
kernfs_break_active_protection(kn)
rdtgroup_ctrl_remove
rdtgrp->flags = RDT_DELETED
/*
* Blocking routine, wait for
* all sub kernfs nodes to drop
* active reference in
* kernfs_break_active_protection.
*/
kernfs_remove(rdtgrp->kn)
rdtgroup_kn_unlock
mutex_unlock
atomic_dec_and_test(
&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
kernfs_unbreak_active_protection(kn)
kfree(rdtgrp)
mutex_lock
mon_event_read
rdtgroup_kn_unlock
mutex_unlock
/*
* Use-after-free: refer to earlier rdtgrp
* memory which was freed in [1].
*/
atomic_dec_and_test(&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
/* kn->active++ */
kernfs_unbreak_active_protection(kn)
kfree(rdtgrp)
Fix it by moving free_all_child_rdtgrp() to after kernfs_remove() in
rdtgroup_rmdir_ctrl() to ensure it has the accurate refcount of rdtgrp.
Backporting notes:
Since upstream commit fa7d949337cc ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
for older stable trees.
Upstream commit 17eafd076291 ("x86/intel_rdt: Split resource group
removal in two") moved part of resource group removal code from
rdtgroup_rmdir_mon() into a separate function rdtgroup_ctrl_remove().
Apply the change against original code base of rdtgroup_rmdir_mon() for
older stable trees.
Fixes: f3cbeacaa06e ("x86/intel_rdt/cqm: Add rmdir support")
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1578500886-21771-3-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b8511ccc75c033f6d54188ea4df7bf1e85778740 upstream.
A resource group (rdtgrp) contains a reference count (rdtgrp->waitcount)
that indicates how many waiters expect this rdtgrp to exist. Waiters
could be waiting on rdtgroup_mutex or some work sitting on a task's
workqueue for when the task returns from kernel mode or exits.
The deletion of a rdtgrp is intended to have two phases:
(1) while holding rdtgroup_mutex the necessary cleanup is done and
rdtgrp->flags is set to RDT_DELETED,
(2) after releasing the rdtgroup_mutex, the rdtgrp structure is freed
only if there are no waiters and its flag is set to RDT_DELETED. Upon
gaining access to rdtgroup_mutex or rdtgrp, a waiter is required to check
for the RDT_DELETED flag.
When unmounting the resctrl file system or deleting ctrl_mon groups,
all of the subdirectories are removed and the data structure of rdtgrp
is forcibly freed without checking rdtgrp->waitcount. If at this point
there was a waiter on rdtgrp then a use-after-free issue occurs when the
waiter starts running and accesses the rdtgrp structure it was waiting
on.
See kfree() calls in [1], [2] and [3] in these two call paths in
following scenarios:
(1) rdt_kill_sb() -> rmdir_all_sub() -> free_all_child_rdtgrp()
(2) rdtgroup_rmdir() -> rdtgroup_rmdir_ctrl() -> free_all_child_rdtgrp()
There are several scenarios that result in use-after-free issue in
following:
Scenario 1:
-----------
In Thread 1, rdtgroup_tasks_write() adds a task_work callback
move_myself(). If move_myself() is scheduled to execute after Thread 2
rdt_kill_sb() is finished, referring to earlier rdtgrp memory
(rdtgrp->waitcount) which was already freed in Thread 2 results in
use-after-free issue.
Thread 1 (rdtgroup_tasks_write) Thread 2 (rdt_kill_sb)
------------------------------- ----------------------
rdtgroup_kn_lock_live
atomic_inc(&rdtgrp->waitcount)
mutex_lock
rdtgroup_move_task
__rdtgroup_move_task
/*
* Take an extra refcount, so rdtgrp cannot be freed
* before the call back move_myself has been invoked
*/
atomic_inc(&rdtgrp->waitcount)
/* Callback move_myself will be scheduled for later */
task_work_add(move_myself)
rdtgroup_kn_unlock
mutex_unlock
atomic_dec_and_test(&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
mutex_lock
rmdir_all_sub
/*
* sentry and rdtgrp are freed
* without checking refcount
*/
free_all_child_rdtgrp
kfree(sentry)*[1]
kfree(rdtgrp)*[2]
mutex_unlock
/*
* Callback is scheduled to execute
* after rdt_kill_sb is finished
*/
move_myself
/*
* Use-after-free: refer to earlier rdtgrp
* memory which was freed in [1] or [2].
*/
atomic_dec_and_test(&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
kfree(rdtgrp)
Scenario 2:
-----------
In Thread 1, rdtgroup_tasks_write() adds a task_work callback
move_myself(). If move_myself() is scheduled to execute after Thread 2
rdtgroup_rmdir() is finished, referring to earlier rdtgrp memory
(rdtgrp->waitcount) which was already freed in Thread 2 results in
use-after-free issue.
Thread 1 (rdtgroup_tasks_write) Thread 2 (rdtgroup_rmdir)
------------------------------- -------------------------
rdtgroup_kn_lock_live
atomic_inc(&rdtgrp->waitcount)
mutex_lock
rdtgroup_move_task
__rdtgroup_move_task
/*
* Take an extra refcount, so rdtgrp cannot be freed
* before the call back move_myself has been invoked
*/
atomic_inc(&rdtgrp->waitcount)
/* Callback move_myself will be scheduled for later */
task_work_add(move_myself)
rdtgroup_kn_unlock
mutex_unlock
atomic_dec_and_test(&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
rdtgroup_kn_lock_live
atomic_inc(&rdtgrp->waitcount)
mutex_lock
rdtgroup_rmdir_ctrl
free_all_child_rdtgrp
/*
* sentry is freed without
* checking refcount
*/
kfree(sentry)*[3]
rdtgroup_ctrl_remove
rdtgrp->flags = RDT_DELETED
rdtgroup_kn_unlock
mutex_unlock
atomic_dec_and_test(
&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
kfree(rdtgrp)
/*
* Callback is scheduled to execute
* after rdt_kill_sb is finished
*/
move_myself
/*
* Use-after-free: refer to earlier rdtgrp
* memory which was freed in [3].
*/
atomic_dec_and_test(&rdtgrp->waitcount)
&& (flags & RDT_DELETED)
kfree(rdtgrp)
If CONFIG_DEBUG_SLAB=y, Slab corruption on kmalloc-2k can be observed
like following. Note that "0x6b" is POISON_FREE after kfree(). The
corrupted bits "0x6a", "0x64" at offset 0x424 correspond to
waitcount member of struct rdtgroup which was freed:
Slab corruption (Not tainted): kmalloc-2k start=ffff9504c5b0d000, len=2048
420: 6b 6b 6b 6b 6a 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkjkkkkkkkkkkk
Single bit error detected. Probably bad RAM.
Run memtest86+ or a similar memory test tool.
Next obj: start=ffff9504c5b0d800, len=2048
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Slab corruption (Not tainted): kmalloc-2k start=ffff9504c58ab800, len=2048
420: 6b 6b 6b 6b 64 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkdkkkkkkkkkkk
Prev obj: start=ffff9504c58ab000, len=2048
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Fix this by taking reference count (waitcount) of rdtgrp into account in
the two call paths that currently do not do so. Instead of always
freeing the resource group it will only be freed if there are no waiters
on it. If there are waiters, the resource group will have its flags set
to RDT_DELETED.
It will be left to the waiter to free the resource group when it starts
running and finding that it was the last waiter and the resource group
has been removed (rdtgrp->flags & RDT_DELETED) since. (1) rdt_kill_sb()
-> rmdir_all_sub() -> free_all_child_rdtgrp() (2) rdtgroup_rmdir() ->
rdtgroup_rmdir_ctrl() -> free_all_child_rdtgrp()
Backporting notes:
Since upstream commit fa7d949337cc ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
in older stable trees.
Fixes: f3cbeacaa06e ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: 60cf5e101fd4 ("x86/intel_rdt: Add mkdir to resctrl file system")
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1578500886-21771-2-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
