ath.git patches for 4.10. Major changes:
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com>
Cc: <stable@vger.kernel.org> #4.8+
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop duplicate header vmalloc.h from ath5k/debug.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
num_descriptors and descriptor_size needs to be
checked for:
1) not being negative values
2) no overflow occurs when these are multiplied
together as done in wil_pmc_read.
An overflow of two signed integers is undefined
behavior.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The usb_*_msg() functions expect a timeout in msecs but are given HZ,
which is ticks per second. If HZ=100, firmware download often times out
when there is modest USB utilization and the device fails to initialize.
Replaces HZ in usb_*_msg timeouts with 1000 msec since HZ is one second
for timeouts in jiffies.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare the structure ath_bus_ops as const as it is only passed as an
argument to the function ath9k_init_device. This argument is of type
const struct ath_bus_ops *, so ath_bus_ops structures with this property
can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ath_bus_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1,e2;
@@
ath9k_init_device(e1,e2,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ath_bus_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ath_bus_ops i;
File size before:
text data bss dec hex filename
1295 232 0 1527 5f7 ath/ath9k/ahb.o
File size after:
text data bss dec hex filename
1359 176 0 1535 5ff ath/ath9k/ahb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f28 ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Radar pulse and spectral scan reports are provided by the HW
with the ATH9K_RXERR_PHY flag set. Those are forwarded to
the dfs-detector and spectral module for further processing.
For some older chips, the pre-conditions checked in those
modules are ambiguous, since ATH9K_PHYERR_RADAR is used to
tag both types. As a result, spectral frames are fed into
the dfs-detector and vice versa.
This could lead to a false radar detection on a non-DFS
channel (which is uncritical), but more relevant it causes
useless CPU load for processing invalid frames.
This commit ensures that the dfs-detector and spectral
collector are only fed when they are active.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is what is in the laptop:
01:00.0 Network controller [0280]: Broadcom Limited BCM43142 802.11b/g/n [14e4:4365] (rev 01)
Subsystem: Dell Device [1028:0018]
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at b0400000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [40] Power Management version 3
Capabilities: [58] Vendor Specific Information: Len=78 <?>
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [d0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-9a-ff-ff-f3-40-b8
Capabilities: [16c] Power Budgeting <?>
With the patch, I can see:
bcma: bus0: Found chip with id 43142, rev 0x01 and package 0x08
bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x28, class 0x0)
bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x21, class 0x0)
bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x16, class 0x0)
bcma: bus0: Core 3 found: UNKNOWN (manuf 0x43B, id 0x368, rev 0x00, class 0x0)
bcma: bus0: Bus registered
The wifi is not currently supported by brcmsmac yet:
brcmsmac bcma1:1: mfg 4bf core 812 rev 33 class 0 irq 18
brcmsmac: unknown device id 4365
So don't expect a working wifi from this patch :).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: <linux-wireless@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty
but instead continues polling after the rxq status stays clear; bringing
down the interface takes about six seconds from this alone.
Speed up path by exiting rxq loop once status repeatedly polls empty.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Reviewed-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The scan results for scheduled scan as retrieved from the device
have changed. A field has been added which is not needed. However,
the appended info is. Luckily they are versioned so check that to
find out the location of the appended data.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can specify the interval for the scheduled scan. This
interval is found in scheduled scan plan. The driver supports only
one plan, which is legacy behaviour.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the .sched_scan_start() callback a condition was checked whether a
normal scan was ongoing. However, there is no need for this check as
it is ok to start the scheduled scan irrespective whether or not a
normal scan is ongoing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can provide list of channels in the schedule scan request.
This was ignored so all channels supported and allowed by the device
were used. This patch configures the device to use the channels as
listed in the request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework .sched_scan_start() callback moving actual configuration of
the device in pno source file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_pno_config() function handles two configurations in
firmware. Split it and have caller sort out what is needed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For scheduled scan we initiate an escan in firmware to obtain more
info missing from the scheduled scan notification we get from firmware.
For upcoming functionality this is also required so make it a bit
more generic.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the number of parameters as the removed ones can be obtained
through struct brcmf_if parameter.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ssids list in the scheduled scan request were not properly taken
into account when configuring in firmware. The hidden bit was set for
any ssid resulting in active scanning for all. Only set it for ssids
that are in the ssids list.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introducing new source file for pno related functionality. Moving
existing pno functions.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This chip was already supported, but seems a device came up giving
a different chip identifier. So adding that effectively mapping to
the same firmware file as for 43340 chip.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rev6 of pcie host dongle interface protocol, host needs to maximum
supported ring number from dongle shared memory and set up ring buffer
and ring indices offset accordingly.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell Wifi PCIe modules don't always behave nicely for PCIe power
management when their firmware hasn't been loaded, particularly after
suspending the PCIe link one or more times. When this happens, we might
end up spinning forever in this status-polling tight loop. Let's make
this less tight by adding a timeout and by sleeping a bit in between
reads, as we do with the other similar loops.
This prevents us from hogging a CPU even in such pathological cases, and
allows the FW initialization to just fail gracefully instead.
I chose the same polling parameters as the earlier loop in this
function, and empirically, I found that this loop never makes it more
than about 12 cycles in a sane FW init sequence. I had no official
information on the actual intended latency for this portion of the
download.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_usb_probe() defines and sets bcd_usb but does not use it,
Compiling with W=1 gives the following warning, fix it.
mwifiex/usb.c: In function ‘mwifiex_usb_probe’:
mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable]
The unused variable seems to be present since 4daffe354366 which introduced
mwifiex_usb_probe().
Fixes: 4daffe354366 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 92263a841b15 introduced mwifiex_deaggr_sdio_pkt which initializes
variable pkt_type but does not use it. Compiling with W=1 gives the following
warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’:
mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable]
Fixes: 92263a841b15 ("mwifiex: add SDIO rx single port aggregation")
Cc: Zhaoyang Liu <liuzy@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_sdio_resume() intializes pm_flag, just like
mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’:
mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable]
sdio_get_host_pm_caps() is just an acessor, so the call to it is safe
to remove. The unused variable seems to be present since
5e6e3a92b9a4 which introduced mwifiex_sdio_resume().
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 3935ccc14d2c introduced mwifiex_tm_cmd() which initializes
struct mwifiex_adapter* adapter, but doesn't use it.
Compiling with W=1 gives the following warning, fix it.
mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’:
mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable]
Fixes: 3935ccc14d2c ("mwifiex: add cfg80211 testmode support")
Cc: Xinming Hu <huxm@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 429d90d2212b introduced mwifiex_cmd_tdls_oper() which initializes
struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’:
mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable]
Fixes: 429d90d2212b ("mwifiex: add cfg80211 tdls_oper handler support")
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b5413e6b2228 removed all uses of chan_num in mwifiex_config_scan().
Compiling mwifiex with W=1 gives the following warning, fix it.
mwifiex/scan.c: In function ‘mwifiex_config_scan’:
mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable]
Fixes: b5413e6b2228 ("mwifiex: increase the number of nodes in command pool")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit bec568ff5107 removed the last remaining usage of struct
mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to
mwifiex_del_virtual_intf().
Compiling mwifiex/ with W=1 gives the following warning, fix it.
mwifiex/main.c: In function ‘mwifiex_fw_dpc’:
mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
Fixes: bec568ff5107 ("mwifiex: failure path handling in mwifiex_add_virtual_intf()")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move the dev_info call that attempts to show the rate used before it is set.
Signed-off-by: Barry Day <briselec@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Barry Day <briselec@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I get the following UBSAN warning during boot on my laptop:
================================================================================
UBSAN: Undefined behaviour in drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:280:21
index 32 is out of range for type 's16 [32]'
CPU: 0 PID: 879 Comm: NetworkManager Not tainted 4.9.0-rc4 #28
Hardware name: LENOVO Lenovo IdeaPad N581/INVALID, BIOS 5ECN96WW(V9.01) 03/14/2013
ffff8800b74a6478 ffffffff828e59d2 0000000041b58ab3 ffffffff8398330c
ffffffff828e5920 ffff8800b74a64a0 ffff8800b74a6450 0000000000000020
1ffffffff845848c ffffed0016e94bf1 ffffffffc22c2460 000000006b9c0514
Call Trace:
[<ffffffff828e59d2>] dump_stack+0xb2/0x110
[<ffffffff828e5920>] ? _atomic_dec_and_lock+0x150/0x150
[<ffffffff82968c9d>] ubsan_epilogue+0xd/0x4e
[<ffffffff82969875>] __ubsan_handle_out_of_bounds+0xfa/0x13e
[<ffffffff8296977b>] ? __ubsan_handle_shift_out_of_bounds+0x241/0x241
[<ffffffffc0d48379>] ? bcma_host_pci_read16+0x59/0xa0 [bcma]
[<ffffffffc0d48388>] ? bcma_host_pci_read16+0x68/0xa0 [bcma]
[<ffffffffc212ad78>] ? read_phy_reg+0xe8/0x180 [brcmsmac]
[<ffffffffc2184714>] qm_log10+0x2e4/0x350 [brcmsmac]
[<ffffffffc2142eb8>] wlc_phy_init_lcnphy+0x538/0x1f20 [brcmsmac]
[<ffffffffc2142980>] ? wlc_lcnphy_periodic_cal+0x5c0/0x5c0 [brcmsmac]
[<ffffffffc1ba0c93>] ? ieee80211_open+0xb3/0x110 [mac80211]
[<ffffffff82f73a02>] ? sk_busy_loop+0x1e2/0x840
[<ffffffff82f7a6ce>] ? __dev_change_flags+0xae/0x220
...
The report is valid: doing the math in this function, with an input value
N=63 the variable s16tableIndex gets a value of 31. This value is used as
an index in the array log_table with 32 entries. But the next line is:
s16errorApproximation = (s16) qm_mulu16(u16offset,
(u16) (log_table[s16tableIndex + 1] -
log_table[s16tableIndex]));
With s16tableIndex + 1 we are trying an out-of-bounds access to the array.
The log_table array provides log2 values in q.15 format and the above
statement tries an error approximation with the next value. To fix this
issue add the next value to the array and update the comment accordingly.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will read fw_cap_info filled by firmware to check whether to
skip ADHOC related commands or not. Also, IBSS_COALESCING_STATUS
command has been moved from init path to adhoc network creation
path.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c:1559:6: warning:
symbol 'rtl8192eu_power_off' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to obtain retry count for a given rate we need to pass the
full struct ieee80211_tx_info to the function setting the rate in he
TX descriptor.
This uncovered a huge bug where the old code would use struct
ieee80211_rate.flags to test for rate parameters, which is always
zero, instead of the flags value from struct ieee80211_tx_rate.
Time to find a brown paper bag :(
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the mac80211 provided rate for RTS rather than the hard coded
24Mbps as suggested by the vendor drivers.
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu suffered from two issues when reloading the driver.
The same problems as with the 8723bu where REG_RX_WAIT_CCA bits 22 and
23 didn't get set in rtl8192e_enable_rf().
In addition it also seems prone to issues when setting REG_RF_CTRL to
0 intead of just disabling the RF_ENABLE bit. Similar to what was
causing issues with the 8188eu.
With this patch I can successfully reload the driver and reassociate
to an APi with an 8192eu dongle.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The generic disable_rf() function clears bits 22 and 23 in
REG_RX_WAIT_CCA, however we did not re-enable them again in
rtl8723b_enable_rf()
This resolves the problem for me with 8723bu devices not working again
after reloading the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The full RX descriptor is converted so converting tsfl again would
return it to it's original endian value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A device running without RX package aggregation could return more data
in the USB packet than the actual network packet. In this case the
could would clone the skb but then determine that that there was no
packet to handle and exit without freeing the cloned skb first.
This has so far only been observed with 8188eu devices, but could
affect others.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't want to leave the wake IRQ enabled.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit power level in a channel is determined based on the dfs region.
To support regulatory rules dfs region should be configured to device during
set channel request. Also antenna gain values are taken from the mac80211
channel parameters instead of fixed values.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
